Restoring the Appearance of Encaustic Cement Tiles in Chipping Norton

The photographs on this page are of Encaustic Cement tiles where the grout had not been wiped off the surface properly after being laid. This in turn allowed dirt to become easily trapped and they soon became grubby. We see this problem a lot at Tile Doctor where it is commonly referred to has Grout Smears or Grout Haze. The customer from Chipping Norton had tried to remove it themselves without success and decided to give us a call.

Encaustic Cement Tiles Before Cleaning in Chipping Norton

If you haven’t come across them before Encaustic Cement tiles are often hand painted and are available in a range of beautifully artistic patterns. Being cement based however they do need to be sealed for best results.

Burnishing and Sealing Encaustic Cement Tiles

To remove the grout and dirt and restore the look of the tiles I opted to use diamond encrusted burnishing pads. Tile Doctor supply a set of these pads comprising of four pads of increasing grits. I started with the coarse 400-grit burnishing pads running it over the floor with a rotary floor machine and lubricated with a small amount of water. Following this I worked my way through the system, applying Medium 800-grit and Fine 1500-grit pads rinsing off the slurry generated in-between and extracting with a wet vacuum.

The last Very Fine, 3000-grit pad is applied dry with only a little water spayed onto the floor using a process we call a “Spray Burnish”. This really refines the look of the tiles and usefully leaves them dry. This process took up the whole morning and the next step would be to seal the tiles, so I went for lunch at this point to give the tiles more time to dry.

Sealing Encaustic Cement Floor Tiles

To be sure they were dry I tested the floor with a damp meter, the readings were fine, and I was satisfied I could go ahead and apply the sealer.

To seal the tiles, I used two coats of Tile Doctor Colour Grow, this is an impregnating sealer that penetrates and occupies the pores of the tile thus prevent dirt from becoming ingrained there. Colour Grow also leaves a matt finish which is ideal for this type of tile.

Encaustic Cement Tiles After Cleaning in Chipping Norton

With the grout and dirt removed and a sealer in place to protect them this floor will be much easier for the customer to keep them clean in future.

Get the Encaustic Look

If you like the look of Encaustic tiles but don’t want the hassle of having to maintain them it’s worth looking at their equivalent in Glazed Porcelain which are very low maintenance. CTD have a Cuban and Havana range which are inspired by the intricate geometric shapes found in Encaustic tiles, both are made from Glazed Porcelain which doesn’t need to be sealed and are therefore very low maintenance. CTD have over 100 tile shops in the UK and you can also buy on-line or order free samples via their website: www.CTDTiles.co.uk

 

Restoring the Appearance of Grubby Encaustic Cement Tiles in Oxfordshire

Ruined Limestone Tiled Floor Restored in Banbury

If you’re passionate about tiled floors and easily upset I suggest you look away now as believe it or not the photographs below are from a recently laid Limestone tiled floor in Banbury. It had been left in a very poor state by the tiler who had managed to cover in Grout Haze and then in the process of trying to rectify the problem by cleaning it off with acid managed to etch the surface of the Limestone making the situation even worse. Limestone being a calcareous stone can in fact be dissolved by acids, in face it’s not unknown for mildly acidic cleaning products to cause holes to appear in the surface over time.

Restoring Limestone Tiles

To resolve we had to strip back the Limestone surface using a set of burnishing pads, these diamond encrusted pads come in a number of different colours each one does a different job from honing to polishing. I started with the coarse pad together with water and then carried on through the set until I got to the finer pad removing the soiled water with a wet vacuum along the way. Finally when I had dried the floor I used a finishing pad to buff the floor up. This activity took most of the day so left the floor to completely dry overnight.

Sealing Limestone Tiles

The following day I checked the floor to make sure it had dried, which it had and started to seal the floor which was done using a couple of coats of Tile Doctor Colour Grow Sealer which is an impregnating sealer which gets into the pores of the Limestone to prevent dirt being trapped, the formula as well as providing stain protection also enhances the natural colours in the stone.

I think you will agree we achieved a good result given the original condition of the tile. I should also mention that I also gave the customer a finishing pad as they owned a floor machine and using this on the floor even once a month will keep the honed surface tight and keep the seal working longer.
 
 

Limestone Tile Restoration in Oxfordshire