tiled floor

Coloured Slate Tiled Floor Barnard Gate After Cleaning

Cleaning Multi-Coloured Slate Tiled in a Barnard Gate Kitchen

This Multi-Coloured Slate tiled floor in the kitchen of a property in Barnard Gate near Witney was in good solid condition with no damage but had been poorly maintained with layers of sealer applied to un-clean tiled; the new home owners were keen to make this floor into a talking point as you entered the property and asked us to address the problem.

Coloured Slate Tiled Floor Barnard Gate Before Cleaning

Deep Cleaning a Slate Tiled Floor

The first task was to remove the layers of sealer from the tile so on day one the floor was covered with Tile Doctor Remove and Go which was left this to dwell for a while so it could soak into the pores of the slate and penetrate the remaining sealer. The product was then scrubbed into the tile with a Rocky rotary floor scrubber and then rinsed off with clean water and dried with a wet vacuum. The next process was to clean the floor with a strong mix of Tile Doctor Pro Clean to remove the remaining dirt in the floor and to scrub the grout clean, again the rotary floor machine came in useful for this task and again the floor was thoroughly rinsed with clean water a few times and dried with the wet vacuum. I then left the floor for a couple of days to allow enough for it to completely dry before sealing.

Sealing Slate Kitchen Tiles

To seal the slate I first applied a coat of Tile Doctor Colour Grow which is an impregnating sealer the gets into the pores of the stone and also enhances the natural colours. I then applied a few coats of Tile Doctor Seal and Go which is a topical sealer that added a nice sheen finish that the customer wanted.

Coloured Slate Tiled Floor Barnard Gate After Cleaning
The end result was fantastic and the combination of the two sealers really got the best from the slate which is now very much appreciated and loved by the customer.

Colourful Slate tiles Cleaned and Sealed in Oxfordshire

Cleaning Multi-Coloured Slate Tiled in a Barnard Gate Kitchen Read More »

Travertine Tiled Floor After Cleaning Henleyon Thames

Grout Haze removed from Travertine Tiles in Henley-on-Thames

The photograph below taken at a house in Henley-on-Thames shows a Travertine tiled floor covered with grout haze smears across the surface of the tile. The tiler should of dealt with this after laying the floor however removing grout smears from natural stone is tricky as normally you would use acid but Travertine is very sensitive to acid so I suspect the tiler decided against it in-case the tiles were ruined.

Travertine Tiled Floor Before Cleaning Henleyon Thames

Refurbishing Travertine Tiles

The first step was to give the floor a general wash to remove any grit and to get the grout clean so we started by applying a mild dilution of Tile Doctor Pro-Clean which was spread over the floor with particular attention paid to getting the solution into the grout lines where it was scrubbed in with a stiff brush. Next we removed any trace of product by using a wet vacuum and rinsing thoroughly with clean water.

To remove the grout haze and restore the surface polish the floor needed to be burnished which is done using four diamond encrusted burnishing pads applied in the correct sequence of grits from coarse through to super fine. First using coarse pad number 1 we put some clean water on the floor and using our rotary machine slowly burnished the area making sure that we passed over each tile around four times. The coarse pad cuts into the surface grime of the floor and also removes sealers and in this case the grout haze. The resultant soiled water is rinsed away with clean water which in turn is removed using a wet vacuum. This process is then repeated with the remaining pads to hone and polish the floor, rinsing between each pad until a nice polish is built up on the tile. The floor is then given a final rinse and once we were satisfied that all the slurry had been removed we left the floor to dry.

Cleaning Travertine and Limestone Tiles

I returned the next day to seal the Travertine Tile for which I used two coats of Tile Doctor Colour Grow which is an impregnating sealer that will occupy the pores in the stone preventing contaminates getting in there; Colour Grow also brings out the colours in the stone and in this case has done well to bring out the deep brown colours.

Travertine Tiled Floor After Cleaning Henleyon Thames
The floor now looks 100% better and how it should have looked in the first place.

Travertine Tiled Floor Burnished and Sealed in Shropshire

Grout Haze removed from Travertine Tiles in Henley-on-Thames Read More »

Victorian Tiled Floor Oxford After Cleaning

Refreshing a Victorian Tiled floor in Oxford

The Victorian tiled floor shown below comprised of a complex square and diamond pattern contained with a parallel border and must of take a lot of work when it was first installed. It had been a while since it was last given a deep clean and was now looking rather dull and lifeless; we come across a lot of these floors at Tile Doctor and the remedy is a straight forward deep clean and reseal.

Victorian Tiled Floor Oxford Before Cleaning

Restoring Victorian Quarry Tiles

The first task was to clean the floor with a dilution of Tile Doctor Pro-Clean which was left to dwell on the tiles for a short while before being scrubbed in washing the floor down afterwards and extracting it with a wet vacuum to remove the soiled cleaning solution.

This did a reasonable job of cleaning up the tiles but there were some stubborn areas that would need further attention and what I suspected to be remnants of an old sealer. A stronger product was required and so the next step was to cover half the floor with Tile Doctor Remove & Go leave it to dwell for a time and then scrub the floor again with a rotary machine fitted with a scrubbing pad. Again the tiles were rinsed and the dirty cleaning solution removed using a wet vacuum. Once done the process was repeated on the other half of the floor. Working in sections like this allows more room in what was a tight hallway and also ensures the cleaning products don’t dry out.

This process removed all the old seal and drew out the ingrained dirt. I them rinsed the floor with a dilution of Tile Doctor Grout Clean Up to deal with a few stains and grout problems before removing it with the wet vacuum and giving the entire floor a thorough rinse with water which was repeated a couple of times; again the wet vacuum was used to extract the water from the tiles and get them as dry as possible.

Sealing Victorian Tiles

I had finished cleaning the floor and so left for the evening returning four days later to seal the floor. Fortunately the customer had planned a short break away so the tiles were nice and dry and still clean on my return.

To seal I applied a single coat of Tile Doctor Colour Grow which is an impregnating sealer to give a good base followed by three coats of Tile Doctor Seal & Go which is a topical sealer that added the shine the customer required.

Victorian Tiled Floor Oxford After Cleaning
 

Victorian Tiled Hallway cleaning in Oxfordshire

Refreshing a Victorian Tiled floor in Oxford Read More »

Victorian Tiles After Refurbishment in Farringdon

Victorian Tiled Floor Refurbished in Farringdon

Apologies for the first photograph, I realise now it’s a little out of focus but hopefully you can see that the Victorian Tiled Floor pictured (at a residence in the market town of Farringdon, Oxfordshire) was not looking its best and this was mainly due to the fact that the house had recently undergone some extensive building work and had become very dirty in the process.

Victorian Tiles Before Refurbishment in Farringdon

Refurbishing Victorian Tiles

The first thing I did was protect the skirting board and doors from splashes and then to clean the floor I applied a strong dilution of Tile Doctor Pro Clean and this was left to dwell on the floor for a good twenty minutes. It was then worked into the tile using a deck brush and then more Pro-Clean was applied so the floor didn’t dry. I then scrubbed the floor with a rotary floor machine fitted with a scrubbing pad. After I finished the soiled cleaning solution was extracted using a wet vacuum and the whole floor was then rinsed with clean water to remove any trace of cleaning product. The tiles were then inspected and the process re-applied to areas that needed it; I then left the floor for two days so it could dry thoroughly.

Sealing Victorian Quarry Tiles

When I returned the floor was dry so I sealed it using a single coat of Tile Doctor Colour Grow followed by four coats of Tile Doctor Seal & Go. This is a great combination as the Colour Grow impregnates the tile improving the colours and protecting it from within whilst Seal and Go adds a further layer of protection and also added a nice subtle shine that the customer wanted.

Victorian Tiles After Refurbishment in Farringdon
 

Victorian Tiled floor Deep Cleaned and Sealed in Farringdon

Victorian Tiled Floor Refurbished in Farringdon Read More »

Quarry Tiles After Cleaning in Watlington

Quarry Tiled Floor Restored in Office at Watlington

A company based in the 17th century market town of Watlington were renovating their office space and decided to replace the carpet which had been glued to the floor below. Upon further inspection this turned out to be a Quarry Tiled Floor and they were keen to restore it and so we got the call.

Quarry Tiles Before Cleaning in Watlington

Restoring Quarry Tiles

I first covered the whole floor with Tile Doctor Remove and Go, leaving this to dwell for a while whilst I fitted a scrubbing pad to my rotary machine. Once the machine was ready the whole floor was scrubbed followed by a rinse with water; the resultant soil was then extracted from the floor using a wet vacuum. This process removed most of the glue so I repeated the process until satisfied all the glue had gone. Remove and Go lives up to its name and although normally used to remove sealers it will remove most other coatings as well. This process took up most of the day so after the final and thorough rinse I left the floor to dry aiming to come back the next day to seal it.

When I returned the next day the floor had white patches of effervescence on it where salts had been forced up through the tile as the water evaporated; this had to be dealt with before the tiles could be sealed so I spent the second day scrubbing the entire floor with Grout Clean Up to remove it, after finishing the floor was given another thorough rinse to remove any product from the floor and used the wet vacuum again to get it as dry as possible.

Sealing a Quarry Tiled floor

I returned the third day to a nice dry and most importantly clean floor. To seal Quarry tiles I usually go for Tile Doctor Seal and Go as it’s water based (so no smell) and it adds a nice shine to the floor; however in this case being an office environment with a lot of heavy traffic I decided to go with Tile Doctor Colour Grow which is an impregnating sealer that soaks into the pores of the tile and is likely to be more durable, it also enhances the natural colours in the tile leading to a very nice finish.

Quarry Tiles After Cleaning in Watlington
I think you will agree the final result was a remarkable transformation

Commercial Quarry Tiled floor Restored in Oxfordshire

Quarry Tiled Floor Restored in Office at Watlington Read More »

Victorian Floor Oxford After Cleaning

Restoring a Victorian Tiled Floor in Oxford hidden under Parquet

Let me start this story by telling you this was the most challenging floor that I have come across so far. It all started with a request to visit a property in Oxford where they had discovered an original Victorian tiled floor under a parquet floor in the hall.

When I arrived the customer had taken up a small area in the corner and had already tried to remove the black bitumen that the parquet floor was stuck down with, he had made some progress but realized it would be a massive project without the right tools. After I had showed him how much cleaner I could take his patch he booked me to restore the floor, the customer said he would remove the parquet floor himself.

Victorian Floor Oxford Before Cleaning

Removing Bitumen from Victorian Tiles

When I arrived the parquet had been taken up to reveal a completely bitumen covered tiled floor that was very sticky. My first task was to put protection around the doors and skirting before moving on to removing the bitumen which was done by covering the half the floor in a mixture of Tile Doctor Remove and Go combined with Nano Tech UltraClean which was left to soak in for about an hour.

Victorian Floor Oxford Before Cleaning Victorian Floor Oxford Before Cleaning

After this I scrubbed the solution into the floor using a black scrubbing pad on my Rocky floor scrubbing machine, this loosened the bitumen from the floor which was then washed off with water and removed using a numatic wet vacuum. The same process was repeated on the other half of the floor and then the whole process was repeated again on both parts of the floor until it was clear of bitumen. This was arduous work and took a whole day to complete.

Cleaning Victorian Tiles

When I returned the next day I gave the floor a deep clean using a medium dilution of Tile Doctor Pro Clean, like the Remove and Go this was spread over the floor leaving it to dwell for 10 minutes before being scrubbed in using the scrubbing machine fitted with a black pad; again the floor was rinsed clean with water which was removed using the wet vacuum.

After this I applied Tile Doctor Grout Clean Up which is an acidic product that is great at removing grout smears and mineral deposits from tiles, being an acid you can only leave it on the tile for a short while so I worked in 1m square sections at a time on my knees spraying and scrubbing with a deck brush and then rinsing.

When I had finished this process the whole floor was thoroughly rinsed with clean water to ensure there were no cleaning products left on the floor. I then left the floor to dry promising to return a few days later when it had dried.

Sealing Victorian Quarry Tiles

I returned as agreed a few days later to seal the floor with five coats of Tile Doctor Seal and Go which is a great for Victorian tiles as it leaves a nice shine to the floor which is exactly how the customer wanted it. This process does take time however as you have to let the first coat dry before moving onto the next.

Victorian Floor Oxford After Cleaning Victorian Floor Oxford After Cleaning

From start to finish the transformation of the floor was amazing and the customer was very impressed with the results. Although the area was not large this was a very testing floor as bitumen stays sticky and was very difficult to remove even with the correct machines and products.

Victorian Tiled Hall Restored in Oxford

Restoring a Victorian Tiled Floor in Oxford hidden under Parquet Read More »

Terracotta Tiled Floor in Great Bourton After Cleaning

Terracotta Tiled Floor Cleaned and Sealed in Great Bourton

At first glance and this Terracotta tiled floor at a house in the village of Great Bourton looks in good condition, but on closer inspection there were visible white marks where there had been a water leak in previous years and the salts had come through the tiles. The customer also told me she had to wax the floor on a regular basis and was looking for a seal where she didn’t have to do this.

Terracotta Tiled Floor in Great Bourton Before Cleaning 1 Terracotta Tiled Floor in Great Bourton Before Cleaning 2

Cleaning Terracotta Tile

My first task was to protect all the skirting and kickboards with protective tape. I then mixed Tile Doctor Pro Clean with water and spread it over a section of the floor and then left it to dwell for a few minutes. The solution was then scrubbed in with a black pad on a 17inch rotary floor scrubbing machine. I then used a wet vacuum to remove the slurry and rinsed the floor with water. This process was repeated this process until the whole floor was scrubbed and rinsed with any stubborn areas re-treated.

To remove the white salts from the Terracotta I applied Tile Doctor Grout Clean Up over the floor which was scrubbed in and then removed using the wet vacuum. The whole floor was then thoroughly rinsed with water and the wet vacuum used to suck up the water until it the surface was dry.

The photograph below shows the terracotta floor at this stage with the floor clean and stripped back before re-sealing. I left the floor a couple of days at this point to allow it fully dry before applying the sealer.

Terracotta Tiled Floor in Great Bourton After Stripping

Sealing Terracotta Tile

On my return I checked the floor had dried and then applied two coats of Tile Doctor Colour Grow which is an impregnating seal that enhances the natural colour of terracotta, I then added five coats of Tile Doctor Seal and Go which is a topical sealer giving it the nice finish the customer required.

The customer was really pleased with the results and also relieved that she would not have to keep waxing the floor; whilst I was there I demonstrated how to clean the floor using Tile Doctor Neutral cleaner which unlike acidic cleaners will not harm the sealer.

Terracotta Tiled Floor in Great Bourton After Cleaning 1 Terracotta Tiled Floor in Great Bourton After Cleaning 2

The floor looks much better and certainly my customer thought so and left the following feedback on the system.

Very pleasant young man and he has done a great job. The kitchen floor is transformed. Thank you Barry!

Terracotta Floor Cleaned and Sealed in Oxfordshire

Terracotta Tiled Floor Cleaned and Sealed in Great Bourton Read More »

Terracotta Tiled Floor Thame After Cleaning and Sealing

Terracotta Tiled Kitchen Floor Cleaned and Sealed in Thame

This customer had recently moved into a house with a Terracotta Tiled Floor in Thame, Oxfordshire and decided she did not like the colour of the floor grout and also was unable to clean off some back marks in the corners. When I went to view the property I performed a test clean on a sample area to show her that the black marks could be removed and also stripped back the tile show how much cleaner they could look. The work was agreed and I was booked to come back and completely strip the floor tile, reseal it and also change the grout colour.

Terracotta Tiled Floor Thame Before Cleaning

Cleaning Terracotta Tile

On the first day I carefully taped up all the kitchen cupboards and skirting board to protect them from any splashes or damage. Once this was done a strong dilution of Tile Doctor Pro-Clean which is a multi-purpose cleaner and stripper was applied to the Terracotta floor tiles and left to soak into the tile for a while before being worked in with a rotary machine fitted with a black stripping pad and then a floor scrubber.

Once the whole floor had been treated in this manner the now soiled Pro-Clean solution was removed from the floor using a wet vacuum and then the floor rinsed with clean water using a spinner tool attached to the wet vacuum. The spinner tool has been a great investment for us, it applies water under pressure to the floor and at the same time removes it via an adjacent suction connection saving loads of time; it’s also a versatile tool that can also be used for Carpet Cleaning which incidentally we also do.

The Terracotta tile was now stripped of all sealer so the next step was to cleaned the black grout with Grout Clean Up which is a mild acid cleaner that can remedy a number of grout related issues, after this I rinsed the floor again with fresh water. At this point I noticed some of the grout joints had loose or missing grout so the loose grout was removed and new grout applied to the affected areas, I then had to wait overnight so the floor could dry.

Sealing Terracotta Tile

On the second day I set about sealing the floor using two coats of Tile Doctor Colour Grow which as well as protecting the floor also brings out the natural colours in the Terracotta tile. For added protection and to enhance the shine on the floor I then applied a further five coats of Tile Doctor Seal and Go, the combination of the two compatible sealers provided the effect the customer wanted. I then had to wait overnight for the sealer to dry hard.

Grout Colouring

If you recall from the start of this post, the customer also wanted to change the grout colour to a light grey so I came back for a third day to complete this. With the original grout colour being black I was concerned that the dark grout may show through the lighter grey and so I first let the customer know that it might take two coats of Grout Colourant to achieve this. However once I got started colouring the grout using an applicator I noticed that the light grey was consistently covering the black grout and therefore one coat would be sufficient.

Terracotta Tiled Floor Thame After Cleaning and Sealing
When I had finished she was very impressed by the colour of the tile and grout and remarked on how much brighter her kitchen looked. She also asked me to come back later to do the hall floor which is a multi coloured Victorian floor.

Terracotta Floor Cleaned and Sealed in Oxfordshire

Terracotta Tiled Kitchen Floor Cleaned and Sealed in Thame Read More »

Limestone Entrance Hall Burford After Burnishing

Limestone Tiled Entrance Hall Cleaned in Burford

This Limestone tiled floor was located in the entrance hall of a residential property in Burford. I popped round following a cleaning enquiry to provide a quote and did a sample clean on a test area, I was then asked if I could do the whole floor there and then and not wanting to disappoint I managed to shuffle a few appointments round and got on with it.

Limestone-Entrance-Hall-Burford-Before-Cleaning

Cleaning Limestone Floor Tiles

To get the best from this floor I used a set of diamond encrusted burnishing pads which if you have read any of my previous posts you will remember we always recommend these for hard stone floors such as Limestone, Travertine and Marble. They come in four different grades from coarse to very fine and you work your way through them starting off with the coarse stripper pad with a little just water and then carry on with the remaining pads which are a finer and finer grade until the floor is thoroughly cleaned, polished and any previous sealer removed. Next step was to use Tile Doctor Pro-Clean along the grout lines with a stiff brush to get the grout clean. When done the floor was washed down with water which was then removed from the tile using a wet vacuum and then left to dry.

Sealing Limestone Floor Tiles

Once the floor was dry it was sealed using two coats of Tile Doctor Colour Grow which is a colour enhancing sealer which provides maximum stain protection on natural stone floors whilst bringing out the deep colour in the stone. The last step was to buff the floor to a nice shine with a rotary machine fitted with a white buffing pad.

Limestone-Entrance-Hall-Burford-After-Burnishing
The customer was very pleased with the results so much so she booked me to clean the grout on her kitchen floor.

Limestone Floor Cleaned, Polished and Sealed in Burford

Limestone Tiled Entrance Hall Cleaned in Burford Read More »

Victorian Tiled Floor Thame After Cleaning and Sealing

Filling Holes and Restoring Shine on a Victorian Tiled Floor in Thame

The pictures below were taken in the entrance hall of a residence in the market town of Thame in Oxfordshire where the Victorian Floor Tiles although in good condition had become dull, you will see there is also a photograph of part of the tiles where holes had been drilled in the floor (don’t ask). Naturally the owner wanted both problems resolving and so called in their local Tile Doctor.

Victorian Tiled Floor Thame Before Cleaning 1 Victorian Tiled Floor Thame Before Cleaning 2

Restoring Victorian Quarry Tiles

The first task was to clean the floor which I used a dilution of Tile Doctor Pro-Clean which was left to dwell on the tile for around thirty minutes before being scrubbed in. This was a small area so I used a small black scrubbing pad attached to a cordless drill to do this; a stiff scrubbing brush was also run along the grout lines to make sure any staining to the grout was also dealt with. The resulting soiled solution was then removed using a wet vacuum and the tiles rinsed with water.

The next step was to remove some stubborn paint marks for which Tile Doctor Grout Clean-Up was applied and scrubbed in with a stiff scrubbing brush, you have to be very careful with this product as it is an acid so you can’t leave it on the tile for too long however it does resolve all sorts of tile staining problems. Again this was removed with a wet vacuum and the floor rinsed thoroughly with fresh water to remove any trace of the product.

Sealing Victorian Quarry Tiles

When the floor dried I filled the holes in the Victorian Tile with a quick drying flexible grout which was left to dry and then painted using an acrylic paint to colour the grout the same as the different colours in the tile. On close inspection the hole damage is still visible however they are now a lot less obvious.

The next step was to seal the floor using five thin coats of Tile Doctor Seal & Go which adds a nice sheen to the floor as we as providing protection and making it easier to clean going forward.

Victorian Tiled Floor Thame After Cleaning and Sealing 1 Victorian Tiled Floor Thame After Cleaning and Sealing 2

 

Victorian Tiled Hall Restoration in Thame, Oxfordshire

Filling Holes and Restoring Shine on a Victorian Tiled Floor in Thame Read More »

Banbury Slate Flagstone Tiles After Cleaning

Cleaning Old Slate Flagstones Tiles in Banbury

These photographs from the hallway of a house in Banbury where old thick slate tiled floor had been laid and the customer was unable to get them clean or restore any colour back into the stone.

Banbury Slate Flagstone Tiles Before Cleaning

Cleaning Slate Flagstone Tiles

I prepped the skirting boards with masking tape to protect them and then cleaned the floor with a strong dilution of Tile Doctor Pro-Clean which was left to dwell on the floor for a while before being worked into the flagstones by hand using a stiff bristle brush. Normally I use a rotary machine fitted with a scrubbing pad for this but given it was a small area it made sense to get on my hands and knees and apply some elbow grease. This process soon saw the dirt coming out of the tile and the dirty solution was removed using a wet vacuum before rinsing the floor down with clean water. This allowed me to see the stubborn areas where more Pro-Clean and elbow grease were applied, again this was removed and the floor given a thorough rinse using a wet vacuum to remove the liquids and get the floor dry.

Sealing Slate Flagstone Tiles

The floor soon dried so it wasn’t long before I could seal it for which I used two coats of Tile Doctor Colour Grow Sealer which as its name suggest enhances the natural colours in the stone. Once this was dry I continued with a couple of coats of Tile Doctor Seal and Go which adds a nice low sheen to the stone as well as adding to the protection provided by the sealer. As you can see it brought all the dark slate colour back and the sealer should ensure the floor is easy to clean in future.

Banbury Slate Flagstone Tiles After Cleaning
 

Large Slate Flagstones Cleaned and Sealed in Banbury

Cleaning Old Slate Flagstones Tiles in Banbury Read More »

Travertine Floor Brightwell Cum Sotwell

Travertine Tiled Floor Maintained in Brightwell-Cum-Sotwell

This Travertine tiled floor had been laid in a house in the picturesque village of Brightwell-Cum-Sotwell in south Oxfordshire and the owner had decided it was time to have it properly cleaned and re-sealed.

Cleaning Travertine Floor Tiles

The floor was given a wash with Tile Doctor Neutral Cleaner to remove any surface grit and we then filled the small holes, which are quite a common feature of natural travertine, with a matching coloured grout.

This was then followed by the use of the Tile Doctor burnishing system which involves the use of a set of four Burnishing pads fitted to a rotary machine. There are four pads and you start off with a course stripper pad with a little just water and then carry on with the white pad and then the yellow pad until the floor is thoroughly cleaned and any previous sealer removed. Next step was to use Tile Doctor Pro-Clean along the grout lines with a stiff brush to get the grout cleaner.

To bring up the polish on the Travertine tile you then apply the last of the four burnishing pads with gives a final polish.

Travertine Floor Brightwell Cum Sotwell

Sealing Limestone Floor Tiles

To seal the floor and protect it from staining two coats of Tile Doctor Colour Grow as applied; Colour Grow is a colour enhancing sealer which enhanced the natural colours in the stone. Once dry the last step was to buff the floor to a nice shine with a rotary machine fitted with a white pad..

Travertine Floor Cleaned, Polished and Sealed in Oxfordshire

Travertine Tiled Floor Maintained in Brightwell-Cum-Sotwell Read More »

Terracotta Tiles Henley On Thames After

Terracotta Tiled Floor Cleaned and Sealed in Henley on Thames

Another Terracotta tiled floor installed in a conservatory this time in Henley on Thames. The previous sealer was mostly worn away and was no longer offering much protection allowing dirt to get ingrained into the tile and making it difficult to clean effectively resulting in dull looking tile and grout.

Terracotta Tiles Henley On Thames Before

Cleaning Terracotta Tile

I first covered the floor with a mixture of Tile Doctor Pro Clean and water which was scrubbed in with a black scrubbing pad fitted to a slow speed floor scrubber; the soiled solution was removed using a wet vacuum and floor was rinsed down with clean water until all the chemicals were removed again using a wet vacuum to remove the liquids. The process was repeated a number of times until we were happy the tile and grout was clean and took most of the day.

Sealing Terracotta Tile

I left the floor to dry overnight and came back the next day to seal it checking with a moisture meter first to ensure the floor had dried. Terracotta is very porous so in the end it tool eight coats of Tile Doctor Seal and Go to seal the floor, Seal and Go is a water based sealer so it doesn’t give off an odour when it’s drying and also offers durable stain protection together with a low sheen finish.

Terracotta Tiles Henley On Thames After
The floor has been much improved certainly the customer was very pleased with the result.

Terracotta Floor Cleaned and Sealed in Oxfordshire

Terracotta Tiled Floor Cleaned and Sealed in Henley on Thames Read More »

Patchy Terracotta Tiles After Cleaning and Resealing

Terracotta Tiled Kitchen Floor Cleaned and Sealed in Kidlington

I was asked to look at a Terracotta tiled kitchen floor that had just be fitted at a house in Kidlington, it seems the tiles were sticky and patchy and basically looked a bit of a mess. The home owner phoned me on Thursday sounding really upset and as I’m based in the general area I was able to look at the floor later that day.

On inspection I could see that the recently applied sealer had not taken to the floor probably as it was not been allowed to dry properly before sealing. We didn’t know what had been applied on the floor so I did a test on a couple of tiles to see which products would work best to strip the sealer off and then booked the job in for the following Saturday.

Patchy Terracotta Tiles Before

Cleaning Terracotta Tile

I placed my dust sheets down were needed and then I started on the floor by wetting it with a strong dilution of Tile Doctor Pro-clean, this product is quite versatile and being alkaline is safe to use on tile, stone and grout. The floor was then scrubbed using a rotary machine fitted with a black scrubbing pad to agitate and then rinsed down with clean water which was then removed using a wet vacuum and the floor left to dry. This process was repeated until I was satisfied that all the sealer was off and then give the Terracotta a thorough and final rinse to neutralise the floor and make sure there was no chemicals were left on the tile, again a wet vacuum was used to remove the water and I also asked the customer to leave the front and back windows open so the air flow would help dry the floor quicker.

Sealing Terracotta Tile

After a couple of hours I tested the floor with a Damp Meter to confirm the floor had dried and began to seal the tiles using Tile Doctor Seal and Go sealer which is an ideal sealer for Terracotta and also provides the satin finish the customer wanted.

Patchy Terracotta Tiles After Cleaning and Resealing
The area wasn’t the large so I managed to complete the whole Job in one day, needless to say the owner was very pleased that I was able to restore her new floor and oven the moon with the services given only three days had elapsed from the first point of contact to completion.

Patchy Terracotta Tiled Floor Cleaned and Sealed in Oxfordshire

Terracotta Tiled Kitchen Floor Cleaned and Sealed in Kidlington Read More »

Abused Terracotta Conservatory Tiled Floor Kidlington After

Terracotta Tiled Conservatory Floor Cleaned and Sealed in Kidlington

This Terracotta tiled floor installed in a conservatory in Kidlington Oxfordshire was in the worst condition I have ever seen, you should be able to make out a large amount of stains quite easily yourself in the photograph below. The conservatory had been used as a greenhouse with many plant pots sitting directly on the tile which over the years had led to the staining and a build-up of white salts on the surface.

Abused Terracotta Conservatory Tiled Floor Kidlington Before

Cleaning Terracotta Tile

My first step was to give it a good hoover to remove any loose detritus; I then covered the floor in a dilution of Tile Doctor Pro Clean which was left to soak into the Terracotta tile for a few minutes. Pro-Clean I should add is a heavy duty alkaline cleaning product designed for cleaning tile, stone and grout. The next step was to scrub the floor with a black scrubbing pad fitted to a rotary machine; after the scrubbing was done I rinsed with water and removed the waste with a wet vacuum. I then repeated the process again tackling the grout this time with a stiff brush before thoroughly rinsing with a high pressure spinner tool to totally flush the floor. The next step was to rinse the floor with Grout Clean Up which is an acid wash to remove all the salts in the floor, after that I rinsed the floor with the spinner tool again.

Sealing Terracotta Tile

I left the floor to dry overnight and the next day came back to do the sealing taking care to use a moisture meter of the floor first to ensure it had dried sufficiently . I used Tile Doctor Seal and Go to seal the floor, it’s a water based sealer so it doesn’t give off an odour when it’s drying and also offers durable stain protection together with a low sheen finish. It’s also a breathable sealer which will allow moisture to rise up through the floor and evaporate on the surface rather than trapping it beneath the seal.

Abused Terracotta Conservatory Tiled Floor Kidlington After
The floor was transformed by this process and I think you will agree this is confirmed by the before and after photographs above which really speak for themselves.

Terracotta Floor Cleaned and Sealed in Oxfordshire

Terracotta Tiled Conservatory Floor Cleaned and Sealed in Kidlington Read More »

Victorian Quarry Tiled Floor after Restoration in Oxford

Victorian Quarry Tiled Basement Floor Restored in Oxford

This old Victorian Quarry Tiled Floor was discovered in the basement of a large house in Oxford where they had been covered up for years. There were a couple of dead tiles that have had the tops taken of for some reason but the rest were in a reasonable condition given their age.

Victorian Quarry Tiled Floor before Restoration in Oxford

Restoring Victorian Quarry Tiles

On the first day I used a mixture of Tile Doctor Remove and Go combined with Nanotech UltraClean which adds an abrasive element to a powerful coatings remover. I spread this on the Quarry tiled floor and left it for about an hour so it could soak into the tile and breakdown old sealers and soil etc.; I then used a commercial steamer on the floor to aid the cleaning process and bring the dirt and old sealant to the surface. When that was done I rinsed the floor with clean water which was then removed along with the soil using a wet vacuum. The next step was to give the floor a mild acid rinse using Tile Doctor Grout Clean Up to remove any mineral deposits from the surface of the tile and then rinse down again with clean water so all the chemicals were removed. The floor was quite damp at this stage and need to be dry so it could be sealed so I left a dehumidifier there and a damp meter so the customer could test the floor.

Sealing Victorian Quarry Tiles

After a couple of days I got the call from the customer that the floor was now dry so I went round to seal it with five coats of Tile Doctor Seal and Go which is a recommended sealer for Quarry tiles providing good stain protection whilst adding a nice sheen.

Victorian Quarry Tiled Floor after Restoration in Oxford
This floor was 120 years old and the customer had no expectation of any significant improvement and had even considered covering it with wood before giving us a call; I was pleased therefore that we managed to exceed their expectations and breathe new life into this old floor.

120 year old Quarry Tile Renovation in Oxford

Victorian Quarry Tiled Basement Floor Restored in Oxford Read More »

Ruined Limestone Floor Banbury Before

Ruined Limestone Tiled Floor Restored in Banbury

If you’re passionate about tiled floors and easily upset I suggest you look away now as believe it or not the photographs below are from a recently laid Limestone tiled floor in Banbury. It had been left in a very poor state by the tiler who had managed to cover in Grout Haze and then in the process of trying to rectify the problem by cleaning it off with acid managed to etch the surface of the Limestone making the situation even worse. Limestone being a calcareous stone can in fact be dissolved by acids, in face it’s not unknown for mildly acidic cleaning products to cause holes to appear in the surface over time.

Restoring Limestone Tiles

To resolve we had to strip back the Limestone surface using a set of burnishing pads, these diamond encrusted pads come in a number of different colours each one does a different job from honing to polishing. I started with the coarse pad together with water and then carried on through the set until I got to the finer pad removing the soiled water with a wet vacuum along the way. Finally when I had dried the floor I used a finishing pad to buff the floor up. This activity took most of the day so left the floor to completely dry overnight.

Sealing Limestone Tiles

The following day I checked the floor to make sure it had dried, which it had and started to seal the floor which was done using a couple of coats of Tile Doctor Colour Grow Sealer which is an impregnating sealer which gets into the pores of the Limestone to prevent dirt being trapped, the formula as well as providing stain protection also enhances the natural colours in the stone.

I think you will agree we achieved a good result given the original condition of the tile. I should also mention that I also gave the customer a finishing pad as they owned a floor machine and using this on the floor even once a month will keep the honed surface tight and keep the seal working longer.

Limestone Tile Restoration in Oxfordshire

Ruined Limestone Tiled Floor Restored in Banbury Read More »

Limestone Floor Chipping Norton After

Limestone Tiled Floor Maintained in Chipping Norton Holiday Cottage

This Limestone tiled floor was installed in a holiday rental cottage in Chipping Norton which had a regular change of occupants and was in need of a deep clean and polish. To deep clean stone floors such as Limestone, Marble and Travertine the floor needs to be burnished with diamond encrusted pads.

Limestone Floor Chipping Norton Before

Cleaning Limestone Floor Tiles

The floor was given a quick wash with Tile Doctor Neutral Cleaner in order to remove any surface grit and then cleaned using a set of Burnishing pads fitted to a rotary machine. The burnishing pads come in four different types and you work your way through them starting off with a course stripper pad with a little just water and then carry on with the white pad and then the yellow pad until the floor is thoroughly cleaned and any previous sealer removed. Next step was to use Tile Doctor Pro-Clean along the grout lines with a stiff brush to get the grout cleaner. To bring up the polish on the Limestone tiles I used a polishing pad which is the last in the set of the four burnishing pads. The floor was still wet at this stage so an air dryer machine was used to speed up the drying process.

Sealing Limestone Floor Tiles

Once the floor was dry we set about sealing it using two coats of Tile Doctor Colour Grow which is a colour enhancing sealer designed to provide maximum stain protection on natural stone floors whilst bringing out the deep colour in the stone. The last step was to buff the floor to a nice shine with a rotary machine fitted with a white pad.

Limestone Floor Chipping Norton After
 

Limestone Floor Cleaned, Polished and Sealed at a Hale Country Club

Limestone Tiled Floor Maintained in Chipping Norton Holiday Cottage Read More »

Tarmac Stains on Ceramic Tile in Long Hanborough After

Cleaning Tarmac Stained Ceramic Tiles in Long Hanborough

This was a rather unusual request we were asked to look at in the Oxfordshire village of Long Hanborough; they had recently laid a new Tarmac drive and unfortunately it had been walked into the Ceramic tiled kitchen floor leaving a lot of dark staining. After failing to clean the tiles with various supermarket floor cleaners she called in Tile Doctor. Tile Doctor cleaning products are industrial strength so when I arrived I gave her a demonstration on a couple of tiles to show I could clean them and she was amazed at how easy I made it look and booked the work with me.

Tarmac Stains on Ceramic Tile in Long Hanborough Before

Removing Tarmac Stains from Ceramic Tiles

To resolve the problem I scrubbed the floor with Tile Doctor Grout Clean Up which is an acid based product designed to remove grout smears and mineral deposits. Ceramic tiles are very durable however being acid based you can’t leave it on the surface too long so the process was to quickly work it into the stain with a stiff bristle brush, rinse with water and then remove using a wet vacuum.

Tarmac Stains on Ceramic Tile in Long Hanborough After
You can see the difference in the final photograph below where the dark staining has disappeared; the difference in tile colour was due to the lighting. The whole job was completed in one day and the customer was relieved that her floor was not ruined and left the comment below on the Tile Doctor feedback system.

He was thorough and excellent. Very grateful.
M. Rawlings, Long Hanborough

Tarmac Stained Ceramic Tiles Cleaned in Oxfordshire

Cleaning Tarmac Stained Ceramic Tiles in Long Hanborough Read More »

Scroll to Top