Tile Doctor Barry Woodward

Limescale Stained Granite Kitchen Worktop Renovation Oxford

Removing Limescale from a Granite Worktop in an Oxford Kitchen

1 Comment / Oxford Tile Cleaning / Barry Woodward

A client from Oxford was in touch recently regarding their Granite worktop which was heavily stained with limescale build-up and she simply couldn’t get it clean. Oxford is a known hard water area with high readings of calcium carbonate in the water.

Normally granite needs little maintenance however the calcium deposits in the water (often referred to as limescale) are deposited on the worktop surface and over time this slowly builds up.

Limescale Stained Granite Kitchen Worktop Before Cleaning Oxford

There are several household products on the market that can remove limescale however you need to be very careful when using these on natural stone as they can make the problem much worse so wisely, we were asked to resolve the problem.

Removing Limescale from a Granite Worktop and Sink

Granite is not as acid sensitive as Limestone and Marble so to start I carefully applied Tile Doctor Grout Clean-up. This was rubbed into the limescale then rinsed off with water.

This was followed up with a set of six-inch Tile Doctor Burnishing pads applying them in sequence from coarse to extra fine over each part of the Granite countertop. The pads are fitted to a hand buffer and the soil generated by the pads was rinsed off between pads with water.

Granite Kitchen Worktop Aftercare

The granite worksurface does not require an actual sealer to be applied so to finish I sprayed on Tile Doctor Stone Patina Spray and buffed with a cloth to give it a high shine finish. This product is designed for cleaning stone worktops and contains a special ingredient that maintains the lustre so ideal for maintaining the worktops going forward.

Limescale Stained Granite Kitchen Worktop After Cleaning Oxford

Granite is an expensive material and makes the most beautiful and practical worktop you can install in a kitchen. In this case though the Limescale had ruined its appearance, once I had finished buffing the stone however I was pleased to see the kitchen had regained its wow factor.

Professional Renovation of a Limescale Stained Granite Worktop in Oxfordshire

Removing Limescale from a Granite Worktop in an Oxford Kitchen Read More »

Travertine Patio Renovation Henley-on-Thames

Large Pitted Travertine Patio Renovated in Henley-on-Thames

This client in Henley-on-Thames had a large and no doubt expensive Travertine patio installed at the rear of his property. The patio was now looking rather grubby with the usual staining and dirt you would expect with an outside patio that had not been professionally cleaned for several years. Additionally, many holes had formed in the stone which in turn had filled with dirt making effective cleaning difficult.

Travertine Patio Before Renovation Henley-on-Thames

I went over to survey the stone and work out what would need to be done to renovate its appearance. The patio measured 150m2 and I recommended cleaning the patio, filling the holes and then honing the stone with a set of burnishing pads to brink back its appearance, a process which would take three days due to its large size.

Happy with my quote a date was set for the work to start with the proviso that it may need to be re-arranged if the weather was bad.

Deep Cleaning a Travertine Patio

Work started up with an application of Tile Doctor Patio & Driveway Cleaner which was left to dwell so it could breakdown the soils. The patio was then scrubbed with a Carbide Brush fitted to a rotary floor scrubber whilst spraying water onto the stone from the tank fitted to the machine. This hard-wearing brush gets right into the holes in the stone ensuring a very effective clean.

After scrubbing the whole area, the patio was inspected and any stubborn stains spot-treated using the same process. Once I was happy the patio was rinsed thoroughly with water and left it to dry off.

On the second day my attention turned to the holes in the stone which were filled by floating an epoxy grout filler into the holes and grout tiles. Again, it was a very large area to cover so this work took up the whole day.

Travertine Patio During Renovation Henley-on-Thames

On day three I quickly went over the patio again with the carbide brush to remove any detritus that had appeared overnight and then replaced the brush with the first burnishing pad in the set of four to being the honing process.

Applied with water for lubrication the first pad is 400-grit which opens the pores in the stone so the deep-seated dirt can be flushed out. The pad is run over each Travertine tile at least three times and then the soiling that is generated is rinsed off and extracted with a wet vacuum. This process is then repeated with the finer pads which were 800 and 1500 grit, these pads gradually close the pores in the stone and restore its polished honed appearance.

Travertine Patio After Renovation Henley-on-Thames

Once complete the patio was transformed, looked very inviting and was ready for the first of many summer pool parties. I did offer to seal the Travertine when finished but my client decided to do that themselves, it’s a straightforward process, just time consuming. I recommended Tile Doctor Ultra-Seal for this as it won’t alter the natural appearance of the stone and keep it looking very light in colour.

Professional Renovation of a Large Travertine Patio in Oxfordshire

Large Pitted Travertine Patio Renovated in Henley-on-Thames Read More »

Limestone Table Polishing Burford Oxfordshire

Polishing a Limestone table in Burford, Oxfordshire

1 Comment / Limestone Tile Cleaning and Polishing, Witney Tile Cleaning / Barry Woodward

This client from Burford in the Cotswold hills contacted us to see if I could polish up a Limestone table which was now surplus to requirements, and they wanted to sell it. They realised though that the polished appearance was dull and unappealing, so if it was to achieve the best price if would need polishing first.

Limestone Table Before Polishing Burford

We discussed the project over the phone and I explained that although we are more used to polishing stone floors with large diamond burnishing pads there was no reason why the same technique wouldn’t work on the table. For this project we would use smaller six-inch pads that can be fitted to a hand-held buffer machine. Confident I could complete the work and get the table back to its former glory I agreed to call in and demonstrate the process.

Polishing a Limestone Tiled Table

Using a set of small diamond burnishing pads of increasing grits and water I was able to quickly polish a sample area of the table to a nice shine. This newly polished section really highlighted just how dull the rest of the table had become. Like any polished surface it will lose its lustre over time with regular use and potentially cleaning with the wrong products.

Happy my solution was effective, and the price was right, he asked me to continue and polish the whole table. I put tape around the edge of the table to prevent splashes and had a dust sheet on the floor.

Next using a flex polishing machine fitted a six-inch 200-grit pad the stone was lightly cut back to remove the staining and cup marks. A little water is used during this process to help lubricate and a sponge with more water is used afterwards to remove the slurry which is generated. This process was then repeated using 400, 800, 1500 and finally a 3000-grit pads until the Limestone was polished to a honed finish. Again, the slurry was sponged away after each pad.

Sealing a Limestone Table

Then to get a very deep durable Tile Doctor Shine Powder was applied which is ground into the stone using a White buffing pad. Once this had dried, I buffed the table with another White pad to leave table looking like new.

Limestone Table After Polishing Burford

The client was delighted with the finished result and considered keeping it for a moment! However, they were satisfied that they could now sell it for a good price. For the maintenance cleaning of polished stone tables and countertops we recommend Tile Doctor Stone Patina Spray which is very easy to apply and helps protect the polish.

Although we specialise in the maintenance of tiles, stone or grout, mainly involving floors, but from time to time we do get asked to do something different such as resurfacing stone tables or work surfaces. It makes a nice change to complete something different and is very satisfying when the results are as good as this.

Professional Restoration of a Limestone Table in Oxfordshire

Polishing a Limestone table in Burford, Oxfordshire Read More »

Quarry Tiled Shop Floor Renovation Henley-on-Thames

Quarry Tiled Shop Floor Renovation in Henley-on-Thames

1 Comment / Grout Cleaning, Henley-on-Thames Tile Cleaning, Quarry Tile Cleaning / Barry Woodward

If you want an example of the improvement that we can make to a Quarry tiled floor, then pop into the Farrow & Ball Paint shop in Henley-on-Thames. They were in touch in August this year about renovation of their very well-worn Red and Black quarry tiled floor, which after many years of commercial foot fall was now in need of deep cleaning and sealing.

I visited the property to survey the floor and discuss with them the work that needed to be done. I was confident we could make a big improvement to the floor and would soon have the shop looking very much more welcoming.

Red Black Quarry Tile Before Renovation Henley-on-Thames Paint Shop

Being a shop, the work had to be done out of hours, so we discussed the options and decided on starting work at 5pm on a Sunday evening and working through the night. I provided a quote for the work which they were happy to accept, and a date set for the work to begin.

Cleaning a Quarry Tiled Paint Shop Floor

The first process was to remove what was left of the old sealer and soiling by putting down a strong dilution of Tile Doctor Pro-Clean. I left this to dwell and soak into the tile and grout for ten minutes before scrubbing it in with a a rotary machine fitted with a silicon carbide brush.

Once all the tiles had been scrubbed, the floor was rinsed with water and the soiling extracted using an industrial wet vacuum. The floor was then expected and the process repeated on those areas that needed more work.

Next, the floor was treated to an acid rinse using Tile Doctor Grout Clean-up which is a mild acidic product that removes old grout smears, alkaline salt deposits and further cleans up the tiles. This process also neutralises the pH level of the floor following the use of the strong alkaline cleaner used earlier. Again, this was then rinsed off the floor with water and removed with the wet vacuum.

Once the tile and grout were clean and free of old sealer the wet vacuum was used to get the floor as dry as possible. Several air movers were placed around the floor to speed up the drying of the floor.

Sealing a Quarry Tiled Paint Shop Floor

After waiting some time for the floor to dry it was then sealed with a couple of coats of Tile Doctor Seal & Go Extra which is a hard wearing acrylic based sealer that leaves a mild sheen and will protect the tiles for many years to come.

I finished at 4am.

Red Black Quarry Tile After Renovation Henley-on-Thames Paint Shop

As you can see the floor looked fantastic, the owners were over the moon with the improvement. I left them a small bottle of Tile Doctor pH Neutral Cleaner and recommended they purchase some. This is a pH neutral cleaner which can be used every day by their cleaner and it will keep the newly applied sealer in place. It has a lovely fresh smell, so will be very welcoming for their customers. I also recommended our Tile Doctor Maintenance Plan which means will return annually and give the floor a deep clean and seal.

Professional Restoration of a Quarry Tiled Paint Shop in Oxfordshire

Quarry Tiled Shop Floor Renovation in Henley-on-Thames Read More »

Old Quarry Tiled Pub Floor Restoration Chiselhampton

Quarry Tiled Floor Restoration at 400-Year-Old Listed Inn Chiselhampton

1 Comment / Oxford Tile Cleaning, Quarry Tile Cleaning, Wallingford Tile Cleaning / Barry Woodward

This picture below is of an old Quarry Tiled floor at a pub in Chiselhampton called the Coach and Horses Inn which dates to the late 1600’s. The building is listed and has undergone a restoration work by the new owners who called me to look at the Quarry tiled floor.

Old Quarry Tiled Pub Floor Before Restoration Chiselhampton

I paid a visit to the site to survey the tiles and provide a quote, it was immediately clear the floor was in a very bad state, in fact the site foreman said to me “I don’t suppose you can do anything with this, we’re gonna cover it up”. I love a challenge and I carried out a test and found under the rubble, bitumen, plaster and paint was a lovely red floor. Well, they were a little surprised I took it on but I was delighted and got the job!

Restoring and Replacing Old Quarry Tiles

First, I went around with a floor scraper to remove as much of the dusty surface as I could.
I then covered the floor in Tile Doctor Acid Gel and scrubbed it with a 100-grit diamond pad, this revealed that patches of the floor had missing tiles and had been back filled with concrete. I managed to source some replacement tiles from a reclamation yard and replaced the concrete with the tiles. The floor was starting to look great again.

I then covered the floor with Tile Doctor Acid Gel for a second time, but this time scrubbed with a 200-grit diamond pad. The floor was then rinsed with water and a sponge so as not to get the floor too wet. Old floors like these don’t have a damp proof membrane so can take a long time to dry and excess moisture in the floor can increase problems such as efflorescence leaving salty deposits on the tiles. Using gel cleaning products and a minimal amount of water gets around this problem. The floor was then left to dry overnight.

Sealing Old Quarry Tiles

The next day I returned to seal the floor and started by confirming the tiles were dry by taking several moisture readings with a damp meter. All was well and I was able to move onto the next step.

To seal the floor, I used two coats of Tile Doctor X-Tra Seal which brought out the red colour. This is a breathable impregnating sealer; it has an oil-based resin formula so it provides great water repellence and stain protection properties. It’s perfect for internal areas which have moisture issues and can also be used externally.

The first coat revived the colour of the red quarry tiles and the second coat, added a nice subtle sheen. To finish I buffed the floor with a 1500-grit burnishing pad attached to a high-speed buffing machine which produced a natural looking sheen.

Old Quarry Tiled Pub Floor After Restoration Chiselhampton

By the time I had finished the floor was completely transformed and looked great much to the surprise of the foreman. For aftercare I recommended the use of Tile Doctor Neutral Tile Cleaner to ensure the floor remained in this condition for the long term. The product is pH neutral so mild enough to use daily without compromising the newly applied seal.

Professional Restoration of a Quarry Tiled Pub Floor in Oxfordshire

Quarry Tiled Floor Restoration at 400-Year-Old Listed Inn Chiselhampton Read More »

Indian Sandstone Patio Renovation Headington

Large Indian Sandstone Patio Renovated in Headington

1 Comment / Oxford Tile Cleaning, Sandstone Tile Cleaning / Barry Woodward

This Indian Sandstone Patio was laid three years ago at a property in the leafy residential Oxford suburb of Headington. The stone patio has not been properly cleaned since it was laid and I was contacted to see if it could be improved and to fill in the missing grout. You can see from the photograph it was in a shocking state and had completely discoloured after being exposed to the ravages of the UK weather and was now turning green with staining from the trees.

Indian Sandstone Patio Before Deep Cleaning Headington Oxford

Except for the grouting the patio was physically solid and I assured owner that with the right treatment we could renovate the stone to bring back the colour and character of the Sandstone.

Renovating an Indian Sandstone Patio in Headington

On arrival I sprayed the patio with Tile Doctor Patio & Brick Driveway Cleaner and left it to soak in and get to work for about half an hour. The patio was then scrubbed with a rotary machine fitted with a carbide brush. I then rinsed the whole patio with water to remove the soiling. Being a very hot day, it dried very quickly and I was able to inspect the patio and repeat the process focusing on the stubborn staining and to make sure the black spots were removed.

With the patio clean I was able to get a better view of the cement grouting which was cracking and crumbling in places. Rather than patching it up I discussed the problem with the customer we decided that the cement grout had to go completely. To do this I used a mortar rake and an angle grinder, it was laborious work but, in most places it came out easily. With the old cement grouting cleared away a new resin-based grouting compound designed for external use for installed.

Indian Sandstone Patio After Deep Cleaning Grouting Headington Oxford

The whole job took 1 1/2 days to complete and was unrecognisable from the original.
I did recommend sealing the stone with a product such as Tile Doctor X-Tra Seal which is designed for external use however the owners were so pleased with the new look of their patio they decided to leave it as is.

Professional Restoration of an Indian Sandstone Paved Patio in Oxfordshire

Large Indian Sandstone Patio Renovated in Headington Read More »

Damaged Victorian Hallway Floor Fully Restored in Headington

Restoration of Damaged Victorian Hallway in Headington, Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning / Barry Woodward

This is a Victorian hallway floor laid in a classic Black and White diamond pattern at a property in the Oxford suburb of Headington. I suspect the floor is original and dates to 1890 when the house was built. Unfortunately, at some point in its recent past it was damaged during the installation of heating pipes and then backfilled with cement.

Here at Tile Doctor, we see this happen time and time again and have been brough into to restore many period floors such as this example. Gas and heating pipes are the most common reasons for digging up a floor but often the homeowner doesn’t know what to do to restore it so they either live with the defaced floor or more usually cover it with carpet or vinyl.

Victorian Hallway Floor During Restoration Headington Oxford

In this case the property had recently changed hands and the new owner was keen to have the floor restored to its original condition. Fortunately, here at Tile Doctor we are in contact with various companies that make reproduction tiles, so it is not a problem finding matching replacements. In this case I managed to find suitable replacements with a company called Original Features who specialise in reproductions. We visited site to have a look at the job and gave the owners a quote for the work which they were happy to accept.

Cleaning and Repairing a Victorian Tiled Hallway Floor

The first day was spent restoring the damaged floor by carefully cutting out the old cement backfill and replacing to a level that was just deep enough for the replacement tiles to fit. I then made up a concrete adhesive mix and smoothed this in the hole and laid the tiles making sure they were level with the original floor. This was then left to set overnight.

Day two’s focus was cleaning the floor, however given the age of the property I knew it would not have a damp proof membrane, so I was concerned about the use of too much water. Not wishing to exacerbate any damp issues I decided to go with a low moisture cleaning approach.

To do this a gel cleaner known as Tile Doctor Acid Gel was applied to half the floor and then scrubbed into the tiles using a rotary floor machine fitted with a coarse 100-grit diamond pad. Once done this was repeated on the other half of the floor. The tiles were then rinsed with minimal water and the soil extracted with the wet vacuum.

A 200-grit diamond pad was then fitted to the rotary machine, and this was used to further refine the appearance of the tiles using some water for lubrication. This was then followed by a series of Tile Doctor burnishing diamond pads with just water to rinse, clean and force a natural sheen on the floor, again a wet vacuum was employed to vacuum up the slurry. Last step before leaving for the day was to mop the floor with Tile Doctor Neutral Floor Cleaner and left the floor to dry.

Sealing a Victorian Tiled Hallway Floor

Returning on the final day, I set about sealing the Victorian tiles with Tile Doctor X-Tra Seal which is an oil-based sealer that enhances the Black and White colours in the tile. This sealer can also be used externally so it will cope happily with any damp issues that can occur on old floors.

Victorian Hallway Floor After Restoration Headington Oxford

Two coasts were applied allowing each one to dry before applying the next. When the seal was dry, I buffed the floor with a 3000-grit diamond pad to leave a hard-wearing natural sheen. The floor looked great, fully restored, and gave the homeowners a traditional welcoming hallway.

Professional Restoration of a Victorian Tiled Hallway in Oxfordshire

Restoration of Damaged Victorian Hallway in Headington, Oxford Read More »

Travertine Salon Floor Before and After Restoration Kidlington

Pitted Travertine Tiled Floor Restored at Kidlington Hair Salon

1 Comment / Kidlington Tile Cleaning, Travertine Tile Cleaning, Work by Category, Work by Location, Work History / Barry Woodward

The Travertine tiled floor installed at this busy hair salon in the village of Kidlington, had seen a lot of wear of the years and was now looking rather sorry for itself. I suspect the floor hadn’t been professionally maintained and the use of acidic cleaning products had caused holes to form Pitts in the stone which then trapped dirt. Owners of stone floors should be careful what they use to clean their floors with, as many products can dissolve the calcium in the stone over time. If a sealer has been applied, they will strip that off the floor first leaving the stone vulnerable to dirt which becomes ingrained in the stone and is difficult to remove.

Travertine Floor Before Clean Seal Kidlington Hair Salon

The natural colours in this stone which were a mixture of red and green hues which are most unusual for travertine, however due to the accumulation of dirt in the pores of the stone it was difficult to appreciate. I discussed with the client the work needed to renovate the stone and agreed a price for the work. This salon was still closed at this point due to lockdown and the salon owner wanted to have the stone floor renovated as soon as possible in time for re-opening.

Cleaning a Travertine Tiled Hair Salon Floor

First, I gave the floor an initial clean using a strong dilution of Tile Doctor Pro-Clean which as per usual was left for ten minutes to soak into the pores before being scrubbed in with a black pad fitted to a rotary floor buffer. The dirt was then rinsed away with water and extracted with a wet vacuum.

The cleaning process was repeated several times and I then turned my attention to the holes in the Travertine. Holes trap dirt so I spent the rest of the morning carefully filling them with a resin filler in a matching colour.

When the resin was set, I used a set of diamond encrusted buffing pads to hone the stone and blend the filled holes in with the rest of the floor. Lubricating the process with water the first pad to be applied was a very coarse 50-grit milling pad which was followed with a 100 and then 200 grit milling pad. This part of the process opens the pores in the stone so the dirt can be flushed out leaving the stone nice and clean. The next step is to refine the stone using a set of Burnishing pads from 400 up to 1500 grit which closes the pores and rebuilds the polished appearance of the stone. It’s worth mentioning that after each pad I rinsed with more water and the extracted the slurry with a wet vacuum.

Sealing a Travertine Tiled Hair Salon Floor

The floor was left to dry off overnight and I returned the next day to finish the polishing and protect the tiles with the application of a fresh seal. The final step of the polishing process is to apply a very fine 3,000-grit pad to the floor which is done with only a little water sprayed onto the tiles. This last pad really brings up the shine on the Travertine and more importantly it leaves the floor dry which is important when applying a sealer.

With the polishing complete I started applying the first of two coats of Tile Doctor Colour Grow which is the perfect sealer for Travertine as it soaks into the pores of the stone to protect against ingrained dirt and enhances the natural colours in the stone in the process. Once the sealer had dried a buffed off the excess using a white pad.

Travertine Floor After Clean Seal Kidlington Hair Salon

The floor was transformed, and the salon owner was very happy with the work we had carried out. For aftercare cleaning I recommended the use of Tile Doctor Stone Soap which helps to maintain the patina and keep the floor looking its best. I also discussed our annual maintenance plan, where we return annually for a couple of hours to bring up the polish on the stone and top up the sealer, this is a cost-effective solution to keeping the floor in tip top condition.

Professional Restoration of a Travertine Tiled Hallway in Oxfordshire

Pitted Travertine Tiled Floor Restored at Kidlington Hair Salon Read More »

Mouldy Shower Tile Grout Renovation Woodstock

Renovating a Mouldy Discoloured Shower Cubicle in Woodstock

1 Comment / Ceramic Tile Cleaning, Kidlington Tile Cleaning, Oxford Tile Cleaning, Work by Category, Work by Location, Work History / Barry Woodward

Pictured below is a very mouldy Ceramic Tiled Shower Cubicle at a property in the picturesque market town of Woodstock, which is very close to the famous Blenheim Palace and has a long history that dates to the Domesday Book and have many 17th century buildings.

Mouldy Ceramic Tiled Shower Woodstock Before Cleaning

As you can see mould had really got a grip on the white grout around the bottom of the shower and in most other places the grout had become discoloured. Mould and discolouration are a very common problem and is caused by a lack of ventilation in the bathroom as well as the dyes in soap and shampoos.

Most ceramic tiles have a glazed surface and so are fairly impervious to these problems, grout however is a problem due to its cementitious rough nature. I discussed with the client what could be done to restore the appearance of the shower cubicle for them, and they were pleased to hear we could do something about it. Happy with my quotation it wasn’t long before I got instructed to go ahead with the work.

Deep Cleaning a Ceramic Tiled Shower Cubicle

To resolve the problem, I first sprayed the whole shower with Tile Doctor Duo Clean and left it to soak in. The bottle comes with a spray attachment that combines the product with air making it lighter and easier to stick to vertical surfaces. It is a fast effective cleaner which doubles up as a grout cleaner and mould remover.

Whilst the Tile Doctor Duo Clean was doing its magic I fetched the other tools I would need to complete this job. After about 30 minutes I sprayed the cubicle again and started to hand scrub the grout and tiles to remove the mould and dirt. I then rinsed with water and went over the stubborn stains again until I was happy. The walls where then dried with a clean towelling cloth. It is amazing the difference you can achieve with the right grout cleaning product and a lot of elbow grease.

The last step and “prise de la resistance” was to cut out all the original silicone sealant with a sharp knife and then replace with new white sealant which had an anti-mould formula. I am not convinced these anti-mould products work any better to be honest but with mould being such a problem it is definitely worth giving them a go.

Sealing a Ceramic Shower Tiles

The last step was to spray the grout with Tile Doctor Wall Tile and Grout Sealer to help protect the grout, it forms a protective barrier over the tile and the grout, so water just runs straight off the wall and into the shower tray.

Mouldy Ceramic Tiled Shower Woodstock After Cleaning

For after care I recommended the use of Tile Doctor Aqua-Pro which is pH neutral cleaner designed for showers and will help the sealer last longer. Stronger supermarket products can actually strip a sealer off the tile over time so we don’t recommend their use.

I think you will agree the shower cubicle looked transformed by the time I had finished, certainly my client was very happy with the work we had carried out.

Professional Shower Cubicle Cleaning in Oxfordshire

Renovating a Mouldy Discoloured Shower Cubicle in Woodstock Read More »

Terracotta Floor Before After Cleaning in Abingdon

Terracotta Kitchen Floor Deep Cleaned and Sealed in Abingdon

1 Comment / Abingdon Tile Cleaning, Terracotta Tile Cleaning, Work by Category, Work by Location, Work History / Barry Woodward

The photos below are from a customer in Abingdon who had a Terracotta tiled floor in their Kitchen. Kitchens are high traffic areas and overtime the sealer had worn off and now dirt was becoming ingrained in the pores of the Terracotta. Once you get dirt in the pores of a clay tile or natural stone it becomes very difficult to remove and now the floor was not looking its best.

Terracotta Tiled Floor Before Cleaning Abingdon

Unhappy with the appearance of the tiles the owner of the property had been in touch requesting a deep clean and fresh sealer. It was a fairly straight forward job and I was able to provide a quick quotation which was accepted and a data agreed to do the work which would take two days.

Cleaning Terracotta Tile

I started cleaning the Terracotta by doing applying a 1:3 dilution of Tile Doctor Pro-Clean which is our goto alkaline tile cleaner. For this floor I actually ended up using two litres of Pro-Clean diluted in six litres of water. The solution is left to soak into the tile for about ten minutes before being scrubbed in using a 180-grit silicon carbide brush attached to a weighted floor scrubber. These brushes are quite expensive however they do last a long time so well worth the investment for someone in my profession. If you were doing this work yourself a Black Buffing pad would do the trick.

This process worked well on the floor and the cleaning solution was soon dirty with the soil that had been released from the pores of the Terracotta tile. The slurry was rinsed off the floor with water and extracted using Numatic wet vacuum.

Final step of the cleaning process was to give the tiles an acid wash. This is done using a 10:1 dilution of Tile Doctor Grout Clean-Up which is applied to the tiles and then scrubbed in using a soft poly brush fitted to a floor scrubber. This process removes any old grout smears and traces of efflorescence and slightly roughens the surface of the Terracotta tile to ensure a better bond with the sealer. Once done the floor was rinsed with more water and extracted with the wet vacuum leaving the floor as dry as possible before leaving for the day.

Sealing Terracotta Tile

I left the floor to dry off overnight and I returned the next day to seal the floor first checking the tiles were dry by taking a few moisture readings with a damp meter. The readings came back fine so I need not have been concerned however Terracotta tiles being made from clay are very porous so it’s always a good idea to check.

The floor was dry, so I set about applying the first coat of sealer which for this floor I used Tile Doctor Seal and Go Extra. You need to leave around thirty minutes in-between coats and this floor took five coats before it was fully sealed.

Terracotta Tiled Floor After Cleaning Abingdon

Once finished the Terracotta floor looked much cleaner, fresher and the sealer had given the tiles a nice subtle sheen. For aftercare I recommend Tile Doctor Neutral Cleaner which is ideal for the regular cleaning of sealed floors.

Terracotta Floor Deep Cleaned and Sealed in Oxfordshire

Terracotta Kitchen Floor Deep Cleaned and Sealed in Abingdon Read More »

Terracotta Tiled Floor Before After Renovation Witney

Cleaning and Sealing a Terracotta Tiled Floor in Witney

1 Comment / Terracotta Tile Cleaning, Witney Tile Cleaning, Work by Category, Work by Location, Work History / Barry Woodward

I was called in by a client from the Cotswolds market town of Witney who had lifted up a carpet to discover a Terracotta tiled floor underneath. Although the floor was in good physical condition the carpet and underlay had been trapping moisture resulting in White efflorescence staining. Old floors like this one were laid before damp proof membranes became standard so covering them up can cause damp issues. It is important to allow moisture from underneath tiled floors to evaporate unimpeded otherwise moisture can reach out to the walls resulting in rising damp.

Moisture can also penetrate the pores of the clay Terracotta tile potentially leading to its degradation over time and in this case resulted in the appearance of white efflorescent salts being deposited on the tile surface causing unsightly staining.

Cleaning Terracotta Tile

I started cleaning the Terracotta by doing applying strong dilution of Tile Doctor Pro-Clean which is an effective alkaline tile cleaner. For best results I spread the solution on the floor and then leave it to dwell and soak in for up to twenty minutes. This gives the product time to eat into the dirt and old coatings before being scrubbed in with a black pad fitted to a rotary floor machine. This worked very well on the floor and the cleaning solution was soon dirty with the released soil which was removed using a wet vacuum and more water to rinse it away and dry the floor as much as possible.

To remove the white efflorescent staining the floor was given an acid wash using Tile Doctor Grout Clean-up which is designed for removing grout and other mineral stains from tiling. This was brushed into the tile and grout by hand and left to fizz as it reacted with the efflorescence. After another rinse and extract with the wet vacuum the floor was left to dry out for a couple of days. The next step would be to seal the Terracotta and for best results the tile needs to be dry.

Sealing Terracotta Tile

On my return I checked the tiles were dry by taking a few moisture readings with a damp meter. The readings came back fine so I need not have been concerned however Terracotta tiles being made from clay are very porous so its always a good idea to check.

Given the previous issues with damp I knew I would need to use a fully breathable sealer, so I opted to use Tile Doctor Colour Grow. This product will cope well with the moisture and contains a colour enhancing formula that really brings out the red colour of the Terracotta.

Except for a few deep efflorescent stains in the grout, the floor responded very well to the treatment and made a massive improvement to the overall appearance. My client was pleased with the transformation and the newly restored floor matched well with the character of the property.

Terracotta Floor Cleaned and Sealed in the Cotswolds

Cleaning and Sealing a Terracotta Tiled Floor in Witney Read More »

Etched Marble Tiled Countertop Renovation Oxford

Restoring a Damaged Marble Vanity Countertop in Oxford

1 Comment / Marble Tile Cleaning, Oxford Tile Cleaning, Work by Category, Work by Location, Work History / Barry Woodward

Earlier this year I was working on the restoration of a floor in Oxford and the client asked if I would look at the Marble Countertop in the bathroom. I often get asked to look at additional items whilst on site and always happy to see if I can help.

Damaged Marble Vanity Countertop Before Restoration Oxford

Unfortunately, the stone had been cleaned with an unsuitable cleaning product (probably bleach based) and this had etched the surface leaving what appeared to be an unsightly splash mark ruining its appearance.

You do have to be careful with household cleaning products around Marble, always read the label first and check to see if it is safe to use on natural stone before application. Many products are acidic and will etch into Marble as was the case here. I explained to the client what I could do, and she agreed to add the cost onto the quote for the floor I was already doing. I took photos but it is quite hard to see the damage on the images.

Damaged Marble Vanity Countertop Before Restoration Oxford Enlarged

My base in Chalgrove is only 11 miles outside of Oxford so it’s not a problem to pop back and pick up some extra materials if I need them. In this case I was able to bring them along on day two of cleaning and sealing the floor.

Polishing an Etched Marble Vanity Countertop

The only way to restore a polished Marble surface like this is to use a set of diamond encrusted burnishing pads to slowly hone the stone and rebuild the polish. We do this all the time for Marble floors however the pads are the large 17-inch type, for this you need the smaller 6-inch pads which fit a hand buffer and the smaller handheld burnishing blocks.

I started with the handheld diamond blocks and water, starting with the coarse grit to remove the etching, and then working through the grades to leave a smooth but dull finish. I then followed this up with the 6-inch diamond pads in sequence from 800 grit up to 3000 grit to give the top the desired finish.

Sealing a Marble Vanity Top

When it was dry, I sealed it with a coat of Tile Doctor Ultra Seal which is almost invisible. This product is a no-sheen, natural-look, solvent-based penetrating sealer. It gives maximum protection without a shiny finish, so perfect for this vanity top as we wanted the natural colour of the marble to shine through without a shiny finish.

The client was not only over the moon with the work on the floor I had carried out, she was also delighted that I had been able to restore the vanity top in the bathroom as it had been annoying her for some time.

Damaged Marble Vanity Countertop After Restoration Oxford

I discussed with the customer the best way to maintain the Marble surface was to use Tile Doctor Stone Soap cleaner, this is pH balanced and nice and gentle on the marble and helps maintain the patina. It’s supplied as a concentrate so you only need to use a small amount, it can also be used to clean their newly cleaned and sealed floor.

Professional Restoration of a Marble Vanity Countertop in Oxfordshire

Restoring a Damaged Marble Vanity Countertop in Oxford Read More »

Ceramic Tiled Sports Centre Ceramic Shower Tile Banbury Before after Cleaning

Deep Cleaning Anti-Slip Ceramic Tiles at Banbury Sports Centre

1 Comment / Banbury Tile Cleaning, Ceramic Tile Cleaning, Grout Cleaning, Work by Category, Work by Location, Work History / Barry Woodward

We were contacted by a Sports Centre in Banbury regarding the shower facilities in the changing rooms. The rough nature of the anti-slip ceramic tiles had been trapping dirt and it had a build-up of mould in some areas. In addition, the grout on the wall tiles was very discoloured. Obviously, they are very heavily used, so keeping them maintained is paramount to extending the life of the area and of course keeping the customers happy too!

Ceramic Tiled Sports Centre Ceramic Shower Tile Banbury Before Cleaning

With Sports Centres and Gym’s closed around the country this was the perfect time to get some maintenance work done so I when they called, I was happy to take a look. They accepted my quote and I booked them in for a deep clean. With the facility closed to the public I pretty much had the whole facility to myself so social distancing was not a problem.

Banbury is at the North end on Oxfordshire but fortunately the M40 runs right through it, so it doesn’t take long for me to reach it.

Cleaning a Ceramic Tiled Shower Area

My first task was to give the shower tiles a clean with a strong dilution of Tile Doctor Pro-Clean which was sprayed onto the tile. It was left for ten minutes so it could have time to break down the dirt before being scrubbed in.

After inspecting the shower tile, I could see more work would be needed, so I followed this with an application of another Tile Doctor product called Duo Clean. Again, this was sprayed onto all the shower tile including the floor but this time I left it to soak in for an hour. I then scrubbed the walls and floors and rinsed with water. Tile Doctor Duo Clean is a fast, effective double action grout cleaner and mould remover. It cleans up grout and can also remove mould and blackspot from grout and silicone.

It was necessary to repeat the process as the tiles really were dirty, so I repeated the Tile Doctor Duo Clean process left for another hour, then scrubbed and rinsed. There were several shower areas to clean so I moved onto another shower whilst waiting for the first.

Ceramic tiles are sealed at the factory and so will not accept a sealer however grout is cementous and does benefit from being sealed so for this I recommend using an aerosol grout sealer as this is easy to apply.

Once dry the shower looked 100% cleaner and fresher than before unfortunately due to the Sports Centre being closed it will be a while before their customers will be able to appreciate my work.

Ceramic Tiled Sports Centre Ceramic Shower Tile Banbury After Cleaning

Before leaving I advised the centre manager about the common issues with shower tiles and how best to maintain them in the future. I suggested the use of our Tile Doctor Aqua-Pro cleaner which is a pH neutral tile cleaner which could be used in addition to their existing cleaning regime. Hopefully, this information gets passed to the cleaning team who look after the building however it might be a while before they return.

Professional Cleaning of Commercial Shower Tiling in Oxfordshire

Deep Cleaning Anti-Slip Ceramic Tiles at Banbury Sports Centre Read More »

Large Slate Tiled Patio Before and After Restoration Wantage

Large Slate Patio Renovated in Wantage

1 Comment / Slate Tile Cleaning, Wantage Tile Cleaning, Work by Category, Work by Location, Work History / Barry Woodward

These photos of a Slate Patio were taken in 2019 at a property in Wantage. It’s an excellent example of the transformation that can be achieved with stone patios and given the current situation something we would like to do more of.

Although structurally sound the stone looked bleached by the weather and the owner of the property wanted the patio to look like it did when it had been first laid with the colour and character of the Slate restored.

I called in to do site visit to take a closer look. The patio was situated in a sunny spot, so had indeed been bleached by the weather. I discussed what we could do to restore the tiles and they were very happy to go ahead with my quote. We booked to return the following week weather permitting.

Incidentally Wantage is an historic market town that was part of Berkshire, but it has been administered as part of the Vale of White Horse district of Oxfordshire since 1974. The town is situated around 8 miles from Abingdon, with Reading, Newbury and Oxford nearby.

Deep Cleaning a Slate Patio in Wantage

It was a large patio, so I did the work in sections starting with the application of a strong dilution of Tile Doctor Pro-Clean which was left to soak in for ten minutes. This is a concentrated, multi-purpose high-alkaline cleaner, stripper and degreaser that can be diluted at varying strengths, its effective on mildew and algae in areas that have been neglected or subjected to heavy use. Tile Doctor have numerous products that could have been used to renovate stone patio including a dedicated Patio Cleaner which is something I considered using if I needed extra cleaning power.

After ten minutes the solution was scrubbed into the patio with a rotary floor scrubber fitted with a black scrubbing pad. This action lifted the dirt and previous coatings out of the stone turning the cleaning solution into a dark slurry. The slurry was rinsed off and extracted with a wet vacuum.

I then gave the patio an Acid Wash using Tile Doctor Grout Clean-Up to further clean up the stone and disperse any residues, after another rinse with water the patio was dried with a wet vacuum. This product is a cleaner designed to penetrate below the surface to remove light grout smears (grout haze), mineral deposits, rust stains and efflorescence. We also use this product for the removal of most hard water stains, lime deposits and soap scum, it is very effective especially when used in conjunction with Tile Doctor Pro-Clean. Our client had not realised quite how dirty the patio had been!

Sealing a Slate Patio in Wantage

To apply the sealer, I had to wait for a weather window when it would be dry for a few days. I know from experience that applying a sealer to damp stone results can lead to an inconsistent result that customers are rarely happy with.

After returning, I started the sealing process with the application of a pre-sealer called Tile Doctor Stone Oil which soaks into the stone and adds the deep colour the slate really needed. Once this was dry, I applied a single coat of Tile Doctor Ultra Seal to lock in the Stone Oil and add protection.

Slate Patio After Cleaning and Colour Restored Wantage

The Slate patio was completely transformed and needless to say, the owner of the property was very pleased with the result. They were looking forward to using the space and entertaining friends and family.

Professional Restoration of a Slate Tiled Patio in Oxfordshire

Large Slate Patio Renovated in Wantage Read More »

Working Through COVID-19

Events / Barry Woodward

Due to the impact of the Covid-19 Coronavirus it’s become necessary to change our working practices in-line with government guidelines and to take action to minimise health risks to you and our team. At present, none of our team are showing any symptoms of the virus so we are continuing home visits for quotes and to complete scheduled works should it be safe to do so.

All Tile Doctors are aware to look out for the known symptoms of High Temperature and New Continuous Cough. We are aware of the need to self-isolate should it be necessary and should this be the case we will contact you to postpone. We also ask you monitor your own health and contact us should it be necessary for you to postpone for the same reason. Should you be in a high-risk group we recommend contacting us to re-arrange a visit to later in the year.

Naturally the situation could change very quickly and therefore we will no longer ask for any official notice should you wish to postpone or cancel a booking, however we would appreciate a phone call.

Our Tile Doctors are aware of the guidelines and will carry out a risk assessment at every premises they visit. They also understand the importance of observing the following whilst on site:

Avoiding Physical Contact
The importance of Social Distancing
Wearing single use Gloves and Overshoes
Regular hand washing and use of liquid sanitiser
Cleaning Equipment with Detergent after use

We are monitoring Government guidance and will ensure we continually adjust our working practices as required and endeavour to keep you informed. These are challenging times that are impossible to predict, the key is to stay safe and accepting of late changes should they occur.

Regards

Barry Woodward
Oxfordshire Tile Doctor
#TileDoctorUK #weareinthistogether #pulltogether #staystrong

For more information about Covid-19 virus we recommend the following sources:
https://www.nhs.uk/conditions/coronavirus-covid-19/
https://www.gov.uk/government/collections/coronavirus-covid-19-list-of-guidance
https://www.gov.uk/government/publications/covid-19-track-coronavirus-cases

Working Through COVID-19 Read More »

Tumbled Marble Tiled Floor Before After Honing Oxford

Tumbled Marble Floor Honed and Sealed in Oxford

1 Comment / Grout Cleaning, Marble Tile Cleaning, Oxford Tile Cleaning, Work History / Barry Woodward

The owners of this house in the historic city of Oxford contacted Tile Doctor about their Tumbled Marble tiled floor which was not looking its best and was proving difficult to clean effectively. The floor is part of a kitchen/dining room where the grout had darkened substantially with dirt. Oxford is only 12 miles from by base in Chalgrove so I spoke to the client on the phone and arranged an appointment to visit the property and survey the floor.

I could see that sealer had also worn off which is a common problem with natural stone floor and dirt was now trapped in the pores of the stone. They had tried multiple types of household floor cleaners and nothing was getting the floor to look clean, and as it was so light in colour it was really looking quite dirty.

Tumbled Marble Floor Before Cleaning Oxford

We find the best way to renovate hard stone flooring such as Marble is to use a set of diamond burnishing pads which hone the stone and restore its appearance. I recommended this method to the homeowner and worked out a quote. The quote was agreed, and we set a date to do the work which given the size of the floor I calculated would take two days, one to burnish and one to seal.

Cleaning/Repairing a Tumbled Marble Tiled Kitchen/ Dining room Floor

The burnishing process starts with the application of a coarse 400-grit diamond pad which is applied using a rotary floor scrubber and lubricated with water. This pad is run over each tile two to three times and this effectively cleans the stone removing any old sealer in the process.

After rinsing the fine slurry off the floor with more water and extracting with a wet vacuum I turned my attention to the grout. For this I applied a strong dilution of Tile Doctor Pro-Clean along the grout lines and scrubbed it into grout with a stiff brush. The cleaner was then rinsed away with water taking the dirt with it and extracted as before using the wet vacuum.

I then continued to burnish and hone the Marble tiles starting with 800-grit pad and then followed by 1500-grit pad. Each pad was applied with water to lubricate and then the slurry rinsed and extracted off the floor as before. The floor was then left to dry out overnight.

Sealing a Tumbled Marble Tiled Kitchen/ Dining room Floor

On day two I returned and began work by checking the floor was dry enough to seal with a damp meter. All was well so I proceeded to apply the sealer. After discussing sealer options with the client, I opted to use Tile Doctor Colour Grow which is a colour intensifying sealer which enhances the natural colours in the stone. It also provides durable protection by impregnating the pores of the stone preventing dirt from becoming engrained there. I applied two coats of Colour Grow allowing time in-between for the first coat to dry before applying the second.

Before leaving for the day I buffed the floor with a white pad to remove any excess sealer and give the floor a lovely sheen.

Tumbled Marble Floor After Cleaning Oxford

After I had finished the floor looked pristine and my client was over the moon.

Professional Renovation of a Tumbled Marble Tiled Floor in Oxfordshire

Tumbled Marble Floor Honed and Sealed in Oxford Read More »

Slate Tiled Floor Before After Cleaning Abingdon

Revealing Copper Tones in a Coloured Slate Kitchen Floor in Abingdon

1 Comment / Abingdon Tile Cleaning, Grout Cleaning, Slate Tile Cleaning, Work History / Barry Woodward

This customer had recently moved into a property in Abingdon and got in touch about having the coloured Slate floor tiles in the kitchen cleaned and sealed. There was a big variation in appearance from one end of the kitchen to the other and they had a hunch that the Slate had a lot more colours in it than they could see!

Coloured Slate Floor Tiles Before Cleaning Abingdon

I called in to survey the floor and could see that the main issue was the usual problem of the sealer wearing down in the high traffic areas allowing dirt to penetrate and build-up in the pores of the stone. I ran some tests on the tiles and carried out a test clean, the difference in the stone and grout was immediate, and the customer was happy to go ahead and have the whole floor done. We arranged to carry out the work later that month.

Cleaning a Coloured Slate Tiled Kitchen Floor

To clean the floor, I first spread a dilution of Tile Doctor Pro-Clean over a section of the slate tiles. It was then left to soak into the pores of the stone for ten minutes before working it into the slate with a mono rotary floor machine fitted with a black scrubbing pad. I find the pad works well on tiles but can struggle in the recesses of the grout line, so I followed this up by running a stiff brush along the grout lines to get them clean as possible.

After scrubbing the floor in this manner, the dirt was released from the pores of the stone into the cleaning solution and I was then able to extract the resulting slurry from the floor using a wet vacuum. I worked in sections like this until the whole floor was completed. It was surprising how much dirt had been lifted and the Slate floor was a different colour after I had finished.

I then rinsed the floor with water a couple of times and then followed up by scrubbing the floor with Tile Doctor Grout Clean-Up which is an acidic product which cleans the stone further and removes any mineral deposits including grout smears. Being an acidic product, it also counters the alkalinity of Tile Doctor Pro Clean effectively leaving the floor with a neutral pH. I rinsed the floor a couple of times with water and then mopped the floor with Tile Doctor Neutral Floor Cleaner.

That completed the first day, I left for the evening and the floor was left to dry overnight.

Sealing a Coloured Slate Tiled Kitchen Floor

I returned on day two and tested the floor using the moisture meter to make sure it was dry. The readings were good, and I was satisfied it was dry enough to take a sealer. To seal the floor, I applied Tile Doctor Seal & Go which leaves the floor with a sheen finish that the customer wanted. The Slate was quite porous, so it took seven coats to fully seal the floor which took some time and you have to allow for each coat to dry before applying the next.

Coloured Slate Floor Tiles After Cleaning Abingdon

The floor was transformed by the time I had finished, and you can see from the after picture how clean the grout is and how the lovely Copper tones in the stone were now evident; the natural variations in colour were now as they should be. Clearly their hunch had been right!

The customer was very happy and left the following feedback which is always gratefully received as much of our work comes from recommendations.

“Very happy with the service we received. Barry did an excellent job restoring our floor and we wouldn’t hesitate to recommend him.”

Professional Clean of a Coloured Slate Tiled Kitchen Floor in Oxfordshire

Revealing Copper Tones in a Coloured Slate Kitchen Floor in Abingdon Read More »

Black Negro Marquina Marble Shower Tile Before After Polishing Thame

Polishing Black “Negro Marquina” Marble Shower Tiles in Thame

1 Comment / Marble Tile Cleaning, Thame Tile Cleaning / Barry Woodward

I received a call regarding a Black Marble tiled shower that the customer thought he would clean himself and ended up unfortunately making worse. Black Marble adds a very opulent and elegant look to a bathroom, and I suspect this particular variety with the white veins is known as “Negro Marquina” which comes from the Basque region of Spain. I did a quick price check on-line and these tiles are priced around £60 each!

Black Negro Marquina Marble Shower Tiles Before Polishing Thame

If you look closely at the before picture you can see the Marble has lost its shine and has a cloudy appearance. This was due to the use of an acid based cleaner. Thame and Oxford lie in a hard water area, so we often find customers seek to remove Limescale deposits off tile using household products such as Vikal or Cillit Bang. The trouble with these products is they are acidic, and marble is acid sensitive so is easily marked and damaged by their use. You should always read the label before using any cleaner to check if its safe to use on natural stone.

The client was desperate to get the shower room looking how it should when he had selected this beautiful stone.

Cleaning a Marble Tiled Shower

To rectify the problem and restore the polished appearance of the marble I burnished the stone using a small 6 inch 200-grit diamond pad attached to a handheld buffer. This coarse pad cuts back the stone surface to remove the etching, I then used a 400-grit pad which removed the fine scratches made by the first pad. This was followed up with an 800-grit pad which starts the honing process which restores the polished appearance. Water is used to lubricate the process and the tiles are rinsed with water after each stage to remove the fine slurry that is generated.

This is further followed by 1500 and 3000 grit pads the last pad is applied dry with only a little bit of water and leaves the tiles dry and ready for the next stage.

Polishing a Marble Tiled Shower

To further build the polish and protect the stone I applied Tile Doctor Shine Powder buffed in with a white pad. This was applied to the marble wall tiles and then rinsed with water and wiped dry with a clean cloth. When the tiles were fully dry, I buffed the tiles with a clean white pad to show the final polished finish. The tiles looked much improved and very shiny.

Black Negro Marquina Marble Shower Tiles After Polishing Thame

The job was completed in a day and the customer was much relieved that I was able to restore the appearance of the marble. I suggested that he should use Tile Doctor Aqua Pro as his tile cleaner of choice in future. This is pH neutral so will not damage the tiles like the acidic products he had used previously, and it should help him keep the shower room looking sparkling and opulent as initially intended!

Professional Restoration of a Marble Tiled Shower in Oxfordshire

Polishing Black “Negro Marquina” Marble Shower Tiles in Thame Read More »

Quarry Tiled Kitchen Floor Restored in Old Marston

Quarry Tiled Kitchen Floor, Old Marston

1 Comment / Quarry Tile Cleaning, Work History / Barry Woodward

I received a call from this client in Old Marston around two miles north east of the centre of Oxford. They had lifted a lino floor in their kitchen and found an old Quarry Tiled floor underneath and decided to see if they could have it restored.

Quarry Tiled Kitchen Floor Before Restoration Old Marston

I went over to survey the floor and could see that the tiles had been covered with a thin layer of levelling screed to ensure the lino didn’t sink into the recesses. I ran some tests to demonstrate how the screed could be removed which worked well and it was apparent that the tiles underneath were intact and could be renovated. I submitted a quotation for removing all the screed, deep cleaning the Quarry tiles and then sealing the tiles to protect them. The client was really pleased that we could restore the floor and the quote was accepted, with a date booked to do the work.

Removing Screed and Cleaning Kitchen Quarry Tiles

To start the work, I applied undiluted Tile Doctor Grout Clean-up worked in with a small carbide brush attached to a hand-held rotary buffer. The combination of the acid in the Tile Doctor Grout Clean-up combined with the scrubbing action of the brush were effective at removing most of the screed. The small bits of remaining screed were carefully removed by hand, using a floor scraper. The floor was then rinsed with water and the soil removed with a wet vacuum.

For the second phase of the cleaning process I applied Tile Doctor Oxy-Gel which was scrubbed into the floor with a stiff brush rinsing after with water and the soil extracted again using the wet vacuum. After cleaning the floor to remove the dirt I could still see some evidence of the screed on the tiles, so I decided to give the floor an Acid Wash using Tile Doctor Acid Gel which was scrubbed into the floor and rinsed off as before. Tile Doctor Acid Gel is of course an acidic product so once it was removed, I decided to rinse the floor with Tile Doctor Neutral Cleaner to neutralise the pH levels in the floor. The wet vacuum was used again to remove as much moisture from the Quarry tiles as possible before leaving the now clean floor to dry off fully overnight.

Sealing a Quarry Tiled Kitchen Floor

I returned to seal this floor the next day. First, I checked the floor was fully dry with the damp meter, it was within the recommended range, so I was ready to complete the sealing process.

Quarry Tiled Kitchen Floor After Restoration Matt Sealer Old Marston

The client was not too sure if they wanted a matt or sheen finish, so I first put a coat of Tile Doctor Colour Grow on the floor to show them the matt finish. Colour Grow is an impregnating sealer that enhances natural colour and protects from within by occupying the pores in the tile. After reviewing the floor, they decided it was not for them, so I followed up by applying several coats of Tile Doctor Seal & Go which adds a nice sheen finish and is compatible with Colour Grow.

The combination of sealers worked very well together, and they were very satisfied with the final result and of course that we had been able to restore the Quarry tiles.

Quarry Tiled Kitchen Floor After Restoration Gloss Sealer Old Marston

Professional Restoration of a Quarry Tiled Kitchen in Oxfordshire

Quarry Tiled Kitchen Floor, Old Marston Read More »

Salt Stained Quarry Tiled Porch Cleaned Sealed Sutton Courtenay

Victorian Style Quarry Tiled Porch Sutton Courtenay

1 Comment / Quarry Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

The photograph below is of a Large Quarry Tiled porch laid out with a classic Victorian pattern inlay at a house I worked on recently in Sutton Courtenay, Oxfordshire. Sutton Courtenay is a pretty village of on the River Thames to the south of Abingdon and to the northwest of Didcot. Historically it was previously part of Berkshire, but it has been administered as part of Oxfordshire since 1974 when the boundaries changed.

The client was unhappy with the floor, it looked very tired, it had lost all its’ sheen and was covered in large areas of dirty white marks. I discussed with the client what Tile Doctor could do to improve the floor and showed them an example of the cleaning process I would use on part of the floor. They were very happy with the test patch and could see that we could vastly improve the look of the floor. We agreed a price for the work and scheduled in some time in the diary to complete the work for them.

Large Victorian Quarry Tiled Porch Before Cleaning Sutton Courtenay

Cleaning a Victorian Quarry Tiled Hallway Floor

First, I cleaned the floor with a weak dilution of Tile Doctor Pro-Clean which is a highly concentrated, multi-purpose alkaline Tile cleaner, stripper and degreaser. It is a very effective cleaner that removes grease from areas that have been neglected or subjected to heavy use. I scrubbed the product into the floor with a rotary floor scrubber fitted with a soft brush, I then rinsed with cold water and vacuumed up the slurry produced with the wet vacuum.

I then gave the tiles an acid wash using Tile Doctor Acid Gel scrubbed in this time with a black pad, then rinsed with a small amount of water and vacuumed again. This process is designed to counter any alkaline salts known as efflorescence, that may be present in the tiles which is quite a common problem on old floors like this where no damp proof membrane exists under the floor. This action deal with the appearance of white salt staining as moisture rises through the tiles from the subfloor.

I then left the floor to dry which only took a few hours due to the location of the tiles and the usually warm and windy for the time of year.

Sealing a Victorian Tiled Hallway Floor

Returning in the afternoon, I checked the floor was dry with my moisture meter and I was satisfied the floor was ready to be sealed. I chose to seal the floor with Tile Doctor Colour Grow which is an impregnating colour enhancing sealer which will protect the floor from staining from within by occupying the pores in the tile. Critically this sealer is also fully breathable thereby allowing moisture to pass through the tiles and not become trapped under the floor where it could spread to the walls leading to rising damp. I applied two coats initially and then after an hour, I applied a third coat. The floor was then buffed with a white pad to remove any excess and buff up the appearance of the tiles.

Large Victorian Quarry Tiled Porch After Cleaning Sutton Courtenay

The floor looked superb and the client was very happy with the finish, the vibrancy of the colours in the tiles which were enhanced by the sealer was now very intense and the floor looked as it should.

Professional Restoration of a Victorian Quarry Tiled Hallway in Oxfordshire

Victorian Style Quarry Tiled Porch Sutton Courtenay Read More »

Black White Chequered Victorian Tiles Before After Restoration Oxford

Chequered Victorian Tiled Hallway Floor Restoration Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

You may recognise this Chequered Victorian tiled floor from other restorations that I’ve detailed on my website. This in fact is the third house I’ve worked on in the same small road in Oxford where hallway floors like these are a very common feature. In fact, I seem to get a lot of referrals from this area, which is always a pleasure, so I suspect word has got around the neighbourhood. The property sits close to the city centre, of course is famous for the University of Oxford, the oldest in the English-speaking world.

Chequered Victorian tiled hallway Floor Oxford Before Restoration

I visited the property to survey the floor and work out the best method and products to restore the Victorian tiles. The tiles were dotted in paint splashes from decorating and had previously been covered in carpet so there were gripper strips glued around the edges. All of which would need to be removed and then the floor would need a deep clean to remove the years of dirt and then finally it would need to be sealed to protect it going forward. After discussing the work in detail with the owner he was happy to accept my quote and we worked out a convenient date to do the work.

Cleaning a Victorian Tiled Hallway Floor

On my return I carefully prised off the carpet gripper so not to damage the tile. Then I applied a 50:50 mixture of Tile Doctor Oxy-Gel and Tile Doctor NanoTech HBU to the tiles. This creates a strong cleaning/coatings remover that would soften the paint and glue making it easier to remove. I left this to dwell on the floor for about an hour so it could break down the pint and adhesive. I then fitted a coarse 100-grit diamond pad to a rotary floor buffer and scrubbed the floor vacuuming up the resulting residue as I went along. I then repeated the process using a 200-grit pad and repeated the process.

I then spray buffed the floor using water and a 400-Grit burnishing pad followed by a 800-grit pad, rinsing and extracting afterwards with water to remove the fine slurry this process generates.

Old floors like these were laid before the invention of the damp proof membrane which can result in moisture rising through the floor as it evaporates potentially leaving alkaline salt deposits on the surface. This process is known as Efflorescence and although I minimised the use of water during the cleaning process, I was concerned that this may still present a problem later. To neutralise any alkaline salts in the floor that could cause this problem my last action for the day was give the floor an acid wash using Tile Doctor Acid Gel. Once this was done and extracted from the floor, I followed up with a further clean using Tile Doctor pH Neutral Tile Cleaner which was applied with a microfibre cloth. I left the floor to dry off overnight so it could be sealed the next day.

Sealing a Victorian Tiled Hallway Floor

On day two I checked the moisture level in the floor to ensure it had dried overnight. The results were good, so I set about applying the sealer. For this floor I decided to go with three coats of Tile Doctor Colour Grow which is an impregnating sealer that as well as protecting the Victorian tiles form staining also enhances the black and white colours in the tile increasing the apparent contrast. This sealer is also fully breathable so any moisture will be able to evaporate up through the tile and not get trapped under the floor where it could eventually lead to rising damp in the walls.

Chequered Victorian tiled hallway Floor Oxford After Restoration

Before leaving I also discussed maintenance cleaning with the customer and left them a bottle of Tile Doctor Neutral Tile Cleaner which is safe to use on sealed floors and will help keep the tiles looking at their best. It’s supplied in concentrated form so it should last them some time before they run out. The customer was very happy with the end result, she suggested I would be hearing from more neighbours very soon!

Professional Restoration of a Victorian Tiled Hallway in Oxfordshire

Chequered Victorian Tiled Hallway Floor Restoration Oxford Read More »

Travertine Tiled Shower Before After Renovation Abingdon

Mouldy Travertine Tiled Shower Deep Cleaned in Abingdon-on-Thames

1 Comment / Abingdon Tile Cleaning, Travertine Tile Cleaning, Work History / Barry Woodward

This shower cubicle at a house in the historic market town of Abingdon on Thames was tiled with Travertine which with use had become grubby and the grout darkened. The properties in the road were of a similar age and many bathrooms had been upgraded in recent years to make them more modern. This one was no different having been fitted a few years prior.

Travertine Tiled Shower Before Cleaning Abingdon

Travertine is a natural stone material that has unique features and colouring that no other stone can offer. The distinctive design and natural patterns found within Travertine make it very popular choice in bathrooms, where it gives a luxury hotel style feel. It does however need to be maintained if you want it keep that luxury appearance and unfortunately due to the English climate and a general lack of adequate ventilation its quite common for them to attract mould and become stained with dyes from soaps and shampoos. The good news is we have a number of tools and products that we can use to restore their appearance, so they look like a new installation.

Deep Cleaning Travertine Shower Tiles

The main problem was the grout which was badly discoloured. To tackle this the Travertine and grout was sprayed with Tile Doctor Duo Clean and then scrubbed in with a hand brush to remove the mould and ground in dirt from the grout, I then rinsed with water. Duo Clean is a fast and effective double action grout cleaner and mould remover. It cleans up grout and can also remove mould and blackspot from the grout and silicone and it is versatile as it suitable for use on plastic and enamel baths and showers and will not cause any damage to them.

To restore the appearance of the stone I set about re-honing the Travertine tiles using six-inch diamond burnishing pads fitted to a hand buffer. The pads are applied in sequence starting with 400-grit, moving onto 800-grit and finishing with 1500-grit. Applied with water which acts as a lubricant, the process deep cleans and tightens the pores in the stone to improve overall appearance. The tiles are rinsed with water after each pad is applied to remove the soil that is generated.

Sealing a Travertine Tiled Shower Room

Another issue was the silicone strip between the wall tiles and the shower tray which was looking very mouldy and black. Using a sharp knife this was removed and replaced with fresh white mould resistant silicone.

Once the shower area was dry the Travertine wall tile and grout were then sealed with a couple of coats of Tile Doctor Colour Grow. This adds a preventative barrier over the tile and grout allowing water to easily run down the wall, it also improved the appearance of the stone and enhanced the natural brown colours in the Travertine. The customer was very happy with the shower room, it looked much more inviting and they were surprised that I had managed to restore it to the way it looked when it was originally installed.

Professional Renovation of a Travertine Tiled Shower in Oxfordshire

Mouldy Travertine Tiled Shower Deep Cleaned in Abingdon-on-Thames Read More »

Chequered Victorian Tiled Hallway Floor Before After Renovation Oxford

Chequered Victorian Hallway Floor Restored in Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

Our client got in touch to see if we could restore the appearance of her Victorian tiled hallway floor. The property was located on the outskirts of Oxford which as I’m sure your aware is a city that is steeped in history and most famous for its’ University, which is the oldest in the English-speaking world. The architecture in the city is magnificent, much of it dating back to Saxon times.

Chequered Victorian Hallway Floor Tile Before Restoration Oxford

When we arrived as you can see from the first picture, this floor had some missing tiles along the righthand edge which had been back filled with some sort of filler. Fortunately, I’ve done a quite few of these restorations before and knew where to source replacements that would match perfectly. It would be great to restore the floor and get the black and white chequers looking as they should. I discussed a plan to fully restore the floor with the client and agreed a price for the work to be done.

Cleaning/Repairing a Victorian Tiled Hallway Floor

Our first step in the restoration of the floor was to cut out the filler from the floor and clean out the resulting hole so the replacement tiles could be inserted. We then carefully measured the holes and cut the replacement tiles to match. We then laid the tiles with fast curing tile adhesive, this completed the repair part of the restoration and we left the floor for the day, so the adhesive could set overnight.

Day two was phase two of the restoration plan which involved deep cleaning the floor using abrasive burnishing pads. We started with the application of a 100-grit diamond encrusted burnishing pad which was attached to a rotary floor machine and run over the floor with a small amount water to lubricate. The resulting soil was then rinsed off with water and then removed with a wet vacuum. We repeated the process with a whole series of burnishing pads with increasingly finer grades, they included 200, 400, 800 and 1500 grit pads to fully renovate and restore the surface. This process took the whole day and we finished with a 3000-grit pad which gave the floor a slight sheen, this last pad is applied dry with only a little water sprayed onto the tile.

This process deep cleans and refines the Victorian tiles to fully restore their appearance. It also has the benefit of using less water than a chemical cleaning process which is a big advantage on these old floors which were laid before the invention of damp proof membranes and excess moisture can result in the appearance of efflorescence salts as the floor dries.

Sealing a Victorian Tiled Hallway Floor

The floor was again left overnight to dry out and we returned on the third day to seal the floor. The moisture level of the floor was tested first with a damp meter to ensure it was dry, adding sealer to a damp floor is not recommended as it can result in a patchy finish. All was so the Victorian tiles were sealed with a couple of coats of Tile Doctor Colour Grow. This is a colour enhancing sealer that will enhance the contrast of the black and white chequered effect, it’s also fully breathable so will cope well with any moisture. Colour Grow leaves a matt effect to once it had fully dried the floor was buffed with a 3000-grit diamond pad to add a slight sheen to its appearance as requested by the client.

The client was over the moon with the result and really pleased with the repair we had done, the floor looked as it should and they were now able to keep it nice and clean. A warm welcoming hallway now awaited their visitors.

Professional Restoration of a Victorian Tiled Hallway in Oxfordshire

Chequered Victorian Hallway Floor Restored in Oxford Read More »

Grout Clean and Silicone Replaced Oxford

1 Comment / Ceramic Tile Cleaning, Grout Cleaning, Oxford Tile Cleaning, Work History / Barry Woodward

Our clients contacted us in despair with their bathroom. The request was to renovate their ceramic tiled bathroom at a house in Oxford, a beautiful location, as most will know the city is known worldwide as the home of the University of Oxford, which is in fact the oldest university in the English-speaking world, also known as the “city of dreaming spires”. They had tried many supermarket solutions to clean up the grout and sort out the silicone trim, to no avail. The ceramic tiles were in good condition so the specific focus for the client was on treating the dirty grout and silicone trim around the bath.

Bathroom Before Grout Clean and Silicone Replaced Oxford

The grout has gone black with mould in some places and this is a very common problem in UK bathrooms where it thrives in the warm damp conditions and is usually related to a lack of ventilation. The simple action of leaving a window and door ajar after having a shower helps to cross ventilate and can reduce the problem. Of course, this is not always desirable during cold weather so improved mechanical extraction is always better. Another option is to run the shower cold for a few minutes afterwards, in fact some modern showers have this feature built in for that purpose. I discussed the causes with the client, we agreed a quote and arranged a day to complete the work.

Cleaning and Grouting Ceramic Tiled Bathroom in Oxford

I started by spraying the grout with Tile Doctor Duo-Clean, this is a fast and effective double action grout cleaner and mould remover. It cleans up grout and can remove mould and blackspot from grout and silicone and is suitable for use on plastic and enamel baths and showers. I left this to soak in for about 30 minutes, and then worked in sections spraying more Duo-Clean and scrubbing with a grout brush and rinsing each section with water. After cleaning the whole bathroom, I left it for an hour so that the grout had dried. I could then see if there were any places needing a second clean, in this case there were a few stubborn areas and so the process was repeated. Once I was satisfied I had fully cleaned the grout and tiles I took a break and left the bathroom so that the grout would completely dry out. At this stage the tile and grout were already looking much better.

Resealing Ceramic Tiled Bathroom in Oxford

After lunch I carefully removed all the silicone between the bath, sink and the wall tiles with a sharp knife. This is a little time consuming, but it is important to remove all of the old sealant in order to achieve the best finish. This was then cleaned up and then fresh mould resistant silicone put back in its place. This ensures everything is water tight

For aftercare we recommend the regular application of Tile Doctor Oxy-Pro, this is a powerful alkaline product especially formulated for cleaning shower Tile and Grout. It’s a highly effective cleaner that removes soap scum, body oil, mildew and algae from areas that have been neglected or subjected to frequent use. This will keep on top of the problem and ensure the bathroom continues to look nice and clean.

Bathroom After Grout Clean and Silicone Replaced Oxford

The client was very happy with the result which was completed in one day. The bathroom was certainly left looking very fresh, clean and much more appealing.

Re Grouting and Sealing Ceramic Tiles in Bathroom Oxfordshire

Grout Clean and Silicone Replaced Oxford Read More »

Limestone Tiled Floor Before and After Polishing Radcot Oxfordshire

Very Dirty Limestone Tiled Kitchen Floor Cleaned in Radcot

1 Comment / Limestone Tile Cleaning and Polishing, Work History / Barry Woodward

I was asked to clean the Limestone tiled floor of a very old house in the Village of Radcot which is close to the River Thames and dates to the 14th Century. Being close to a river is very scenic but can be problematic and I was told the house had experienced flooding in recent years.

Whilst the Limestone floor clearly wasn’t as old as the house it was definitely in need of some attention to remove the dirty that had become ingrained into the pores of the stone and restore its appearance.

Limestone Tiled Floor Before Cleaning Radcot

Cleaning Limestone Floor Tiles

My first step was to let the floor soak for ten minutes in a strong dilution of Tile Doctor Pro-Clean, which is a strong Tile and Grout cleaner. The product was then scrubbed into the floor using a deck brush to remove any surface dirt. I also took the opportunity to clean up the grout before rinsing off the now soiled cleaning solution with water and extracting it with a wet vacuum.

Next I turned my attention to the stone tiles which would need to be stripped back, re-honed and then sealed to protect them. I find the best way to achieve this on stone is through the application of a set of Diamond encrusted burnishing pads.

I started the burnishing process by fitting a coarse 400 grit no.1 burnishing pad to a floor buffer and running at a slow speed, applied the pad over the whole floor. This coarse pad is designed to strip off old coatings and dirt from the tile. You use a little water to help lubricate and once complete it’s necessary to rinse the area with water to remove the soil that is generated. The next step is to start building back the polished surface with the 800 and then 1500 grit pads which are applied in the same manner.

This floor was left to dry before moving onto the final stage of the polishing process which is to apply the very fine 3000 grit which further restores the appearance of the Limestone tile. This last pad is applied dry with a small amount of water sprayed onto the surface to help bring up the shine.

Sealing Limestone Floor Tiles

With the floor dry I moved onto sealing the tiles in-order to protect them from dirt and staining. I used a couple of coats of Tile Doctor Colour Grow for this purpose as this particular sealer enhances the natural colours in the stone. It’s also an impregnating sealer that works by occupying the pores in the stone thus preventing dirt from becoming ingrained in the stone.

My pictures of the floor are not brilliant but hopefully you can see how much more colourful the floor now looks.

Limestone Tiled Floor After Cleaning Radcot

Limestone Floor Cleaned, Polished and Sealed in Radcot

Very Dirty Limestone Tiled Kitchen Floor Cleaned in Radcot Read More »

Filthy Limestone Fireplace Restored in Oxford

1 Comment / Fireplace Cleaning, Limestone Tile Cleaning and Polishing, Oxford Tile Cleaning, Work History / Barry Woodward

A stone fireplace adds a classic and period look to any home but like the stone floors we deal with its only a matter of time before the appearance degrades, however not from foot traffic but from soot. This process happens so gradually it goes without being noticed until one day you realise it really does need a good clean and the dirtier it gets, the harder it is to clean.

I recently visited a customer living in the historic city of Oxford who had never once cleaned their black Limestone fireplace. One day, they decided to finally clean it but found that it would take a lot more than just a light scrub with some soapy water!

As you can see from the photograph below, the Limestone was extremely dirty, dusty and stained. Upon examining the situation, I decided that the best way to restore the stone to its original condition would be to use a polishing process known as burnishing. Keen to see the natural beauty of the Limestone again, the customer was more than happy to book in the job.

Limestone Fireplace Before Cleaning Oxford

Cleaning and Burnishing a Limestone Fireplace

As I would be focusing solely on the Fireplace, it was necessary for me to start by protecting the surrounding area with tape. I then began the process of burnishing, starting with a 200-grit diamond encrusted handheld burnishing block. I sprayed a small amount of water onto the fireplace to act as a lubricant and rubbed the diamond encrusted block onto the stone.

This coarse grit pad helps to grind away the thick layers of dirt on the surface of the Limestone and starts to gradually polish the surface beneath. I completed the burnishing working in small sections at a time, rinsing with fresh water and wiping excess off regularly as I progressed.

After finishing with the 200-grit block I then repeated the process using a 400-grit block. This block possesses a finer grit and really helped to achieve a high-quality polished effect.
While the Limestone was drying, I treated the black fire grate with the correct grate paste (or polish) which cleaned it and recoloured it.

To complete the cleaning process, I paid attention to the black tiles on the floor. These were cleaned using Tile Doctor Pro-Clean diluted with water, and scrubbed into the stone and grout using a small specialised brush. Finally, I rinsed the area with fresh water and dried it with a towel.

Sealing a Limestone Fireplace

I then had to leave the fireplace to dry for about an hour so it would be ready to seal. To seal the Limestone, I used Tile Doctor Ultra-Seal, which offers the natural looking finish that the customer wanted. This sealer is formulated to provide maximum protection against stains and dirt, and is suitable for use on all types of natural stone.

The customer has decided that although this will no longer be used as a working fireplace it, will certainly give the room a focal point – so she was very happy to have it back to looking its best!

Limestone Fireplace After Cleaning Oxford

Professional Restoration of a Limestone Fireplace in Oxfordshire

Filthy Limestone Fireplace Restored in Oxford Read More »

Refreshing a Victorian Tiled floor in Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

The Victorian tiled hallway shown below had until recently been covered by carpet and was in surprisingly good condition for its age which is a testament to the durability of these floors. My client who lives in Oxford had managed to remove most of the glue that had been used to secure the carpet to the tile but found it had left an imprint on the floor. Unable to take the restoration any further we were asked to remove the ground in grime and seal the floor.

Carpet Covered Victorian Tiled Floor Before Cleaning Oxford

Restoring Victorian Quarry Tiles

My first task was to remove what was left of the carpet adhesive primarily with the aid of scraper which was used carefully along the edges. This removed the thicker parts of the glue but needed more work to remove all the traces; so a 50 grit disc fitted to a handheld machine was run around the edges of the whole floor to complete the job removing the residue and dirt in the process.

I then used a 50 grit milling pad attached to a rotary floor machine to remove the ground in grime and clean the whole floor. The floor was then rinsed with water to remove the soil that was generated afterwards and then the process repeated this with a 100 grit and 200 grit milling pad to fully restore the appearance of the tile.

This process took up most of the day so before leaving I gave the floor an acid wash using a mild dilution of Tile Doctor Grout Clean-up and then followed this with a good rinse and final clean with Tile Doctor Neutral Cleaner.

Sealing Victorian Tiles

Having finished cleaning the floor I left it to dry off completely for three days to ensure it was bone dry before returning to seal it.

To seal I applied Tile Doctor Colour Grow which is an impregnating sealer that protects the tile from within by occupying the pores in the clay, it also enhances the natural colours in the tile in the process and leaves a matt finish.

Carpet Covered Victorian Tiled Floor After Cleaning Oxford

The finished floor looks a lot brighter now it’s now free of all the dirt and glue marks, the new sealer will also ensure it’s easy to clean and keeps its appearance for some time to come.

Victorian Tiled Hallway cleaning in Oxfordshire

Refreshing a Victorian Tiled floor in Oxford Read More »

100 Year Old Brick Floor Renovated in Oxford

1 Comment / Oxford Tile Cleaning, Work History / Barry Woodward

We were contacted by a customer living in Oxford who had a property with a brick floor in the living room that was in a bad state and in need of restoration. Brick has always been used as an alternative flooring material to stone due its durability and low cost. Oxford has a long history dating back over a thousand years so it not unusual to discover something like this in older properties.

The owner believed the floor to be over 100 years old and had been patched up in numerous places in the past with holes filled in with modern bricks and concrete. I was confident we could dramatically improve the floor but naturally give its long history it would never look like it was new again.

100 Year Old Brick Floor Before Cleaning

Restoring a Brick Floor

To remove the dirt I stated with the application of a strong dilution of Tile Doctor Pro Clean, a high alkaline product that is our go to cleaning product. I applied the product to the floor and left it to dwell for twenty minutes before scrubbing into the brick with a black scrubbing pad fitted to a low speed rotary machine. The soiled cleaning solution was then extracted using a wet vacuum and the floor rinsed with water.

With a lot of the dirt removed I could see I would need to use something abrasive to remove the layers of concrete and give the floor a consistent appearance. Fortunately we a number of techniques we can use for dealing with these issues and in this case I opted to apply a series of coarse abrasive milling pads. I started with the 50grit grit pad which is applied by attaching it to a weighted floor buffer and lubricated with water. Then the floor is rinsed and the process repeated with a 100 grit pad and finally a 200 grit pad to finish the process. The pads use industrial diamonds to slowly grind down the surface and improve its appearance. After the final rinse I could see the floor was much improved, I then had to wait for the floor to dry off fully before I could seal it.

Sealing a Brick Floor

On my return the next day I checked the floor with a damp meter to make sure it had dried. All was well so I set about applying a sealer to protect the floor from staining going forward and also make it easier to clean. This sealer I opted for was Tile Doctor Colour Grow which protects the brick from within by become ingrained into the pores of the material and has the added benefit of enhancing the natural colour to bring back the redness of the brick in the process.

I appreciate the photographs are not my best but hopefully you can appreciate the improvement, certainly the customer was very pleased with transformation and left the feedback for me below. In fact they were originally of the opinion that it probably wasn’t salvageable so this was a major bonus.

We went from dirty old brick living room floor to shiny new (looking) floor in the space of two days. Barry called back immediately came round to have a look the same day then set a date and time and met every promise.

Professional Restoration of a Dirty Brick Living Room Floor in Oxfordshire

100 Year Old Brick Floor Renovated in Oxford Read More »

Deep Cleaning a Chequered Vinyl Floors in Oxford Catholic Church

1 Comment / Oxford Tile Cleaning, Vinyl Tile Cleaning, Work History / Barry Woodward

These photos of a Black and White Chequered Vinyl floor are actually from the Holy Rood Catholic Church in Oxford which is part of the North Hinksey Parish. It’s a popular church visited by many parishioners so the floor gets a lot of wear and I was asked to give it a good deep clean and re-seal.

Chequered Vinyl Lino floor Before Cleaning Sealing in Oxford

Cleaning Soiled Vinyl Floor Tiles

The Vinyl tiles had been sealed with a polish before so my first job was to strip the old polish off the floor. Fortunately, I have a good product for doing that in the shape of Tile Doctor Vinyl Strip which is an effective heavy-duty floor polish stripper that quickly removes polish and coatings from vinyl floors.

The Vinyl Strip was applied to the floor, left to soak in for a while and then scrubbed in using a scrubbing pad attached to a rotary machine. I then rinsed the floor with water.

The cleaning process released a lot of dirt from the floor which was rinsed away with water and then extracted using a wet vacuum. Once the floor was clean I was able to check the floor and repeat the process for any stubborn areas that needed extra work and once I was 100% happy I left for the evening.

Sealing a Victorian Tiled Floor

I returned the next day to seal the floor with two coats of Tile Doctor Vinyl Shine applying the first coat in an up and down direction and the second coat side to side.

Vinyl Shine is a high solids polymer floor seal and polish designed to protect and enhance the appearance of Vinyl floor tiles. The formula includes special polymers which produce a ‘Wet Look’ finish whilst enhancing slip-resistance. A first coat seals and protects the floor and a second produces a gloss finish.

This was a huge floor and naturally the Church was open most days so the work was spread over two weeks doing two days each week.

Chequered Vinyl Lino floor After Cleaning Sealing in Oxford

I’m not sure the photographs I took actually do the work justice however my customer was certainly pleased with the difference and left the following glowing testimonial for me.

“Barry and Nick did a great job and was a pleasure to have around, always letting us know what was going to happen next. The final invoice was exactly as his initial quote. We are very impressed with his work and I will definitely contact him for some work in my home.”

Professional Vinyl Tiled Floor Maintenance in Oxfordshire

Deep Cleaning a Chequered Vinyl Floors in Oxford Catholic Church Read More »

Heavily Stained Quarry Tiled Floors Restored in Oxford Shop Conversion

1 Comment / Oxford Tile Cleaning, Quarry Tile Cleaning, Work History / Barry Woodward

This ground floor flat in the City of Oxford had been converted from a shop which as you can imagine, was quite complex. One significant element involved in the conversation was the restoration of an old Quarry tiled floor which ran through the main hallway and had for many years been covered in a commercial linoleum covering.

When the linoleum covering was removed, the sheer amount of glue which had been used to affix it had completely ruined the appearance and condition of the Quarry tiles. There was also a lot of concrete in the bathroom, and our client was keen to have this removed in the hope that the tiles beneath were salvageable.

Quarry Tiled Floor Oxford Before Restoration

Removing Concrete and Glue Stains from a Quarry Tiled Floor

My first task at the property was to deal with the adhesive. I covered the entire floor area with Tile Doctor Remove and Go and then covered it with a plastic sheet and leaving it to soak into the glue and break it down overnight. Remove and Go is powerful stripper with a long-dwell time, formulated to break down adhesives and paint stains, amongst other coatings.

I returned the next day and, removing the plastic sheeting, I scrubbed the floor with a carbon brush attached to a rotary floor scrubber to remove the huge glue deposits. I worked in sections, rinsing each area of the floor with water after it had been scrubbed. Once I had finished the entire floor there was still some glue remaining, so I covered it again with a solution of Remove and Go combined with Tile Doctor HBU Nanotech, which utilises nano-sized particles to get underneath tough stains, dissolve them, and lift them out. I left this solution on the floor for about two hours to dwell and scrubbed it again.

During the next day of work, I used a very coarse 100 grit diamond burnishing pad to manually grind away the remaining stubborn bits of glue. Paying attention to the bathroom, I used a 50-grit coarse milling pad followed up with a 100-grit diamond burnishing pad to do the same to the area of concrete.

The next part of the process was to use Tile Doctor Grout Clean Up to acid wash the floor. This was successful in removing the last bits of cement and the remaining residue of the glue. To complete the cleaning process, I then rinsed the floor with plenty of water and vacuumed up any soiled solution.

Sealing a Quarry Tiled Floor

I opted to leave the floor alone for a couple of days to fully dry off so that it could be sealed upon my return. This is crucial as any moisture or damp issues can damage the performance of the sealer and expose the floor to further ingrained dirt and staining.

To seal the floor, I used Tile Doctor Colour Grow. This is an impregnating sealer that also enhances the natural reddish shades in the Quarry. I applied two coats of the sealer, giving the floor the natural look matte finish the customer desired.

Quarry Tiled Floor Oxford After Restoration

The customer was very impressed with the results of this thorough restoration. She even left the following feedback:

“I cannot recommend this service enough. The Oxford Tile Doctor (Barry) was a superstar: he cleaned up the tiles in my hallway, which were covered in a very thick layer of glue, and removed concrete from the tiles. They now look superb and I’m really happy with the outcome. Barry was always on time, considerate, and kept me up to date. The quote for the job was exactly right. I would not hesitate to recommend him.”

Professional Quarry Tiled Floor Restoration in Oxfordshire

Heavily Stained Quarry Tiled Floors Restored in Oxford Shop Conversion Read More »

Victorian Tiles Refreshed After Property Renovation in Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

When you decide to undertake a complete renovation of a property, it’s inevitable that floors will be in some way affected by the decorating. At this property in Oxford a renovation had just recently taken place, leaving the black and white patterned Victorian tiled floor covered in concrete residue, plaster and paint.

Victorian Tiled Floor Before Cleaning Oxford

Naturally, the property owner was keen to have the appearance of the tiled restored, to match in with the completely rejuvenated house. I was called in to see what could be done to resolve the problems.

Cleaning a Dirty and Stained Victorian Tiled Floor

I started the restoration by rinsing the floor thoroughly using Tile Doctor Grout Clean-Up which is a concentrated phosphoric acid cleaner used to remove the plaster, concrete, paint and adhesive residue. I then rinsed the floor with fresh water to neutralise the chemicals and extracted all the fluids using a wet vacuum.

Following this, I opted to apply a series of diamond burnishing pads to grind off any particularly stubborn instances of residue, rinsing the tiles with water after each.
Unlike the pads, we use to burnish the shine back onto high end polished stone such as Limestone, Marble, and Travertine these pads were very coarse 100 and 200 grit milling pads rinsing with water after each pad and finishing with a 400 grit burnishing pad. This process thoroughly cleaned the floor and removed all the paint.

Sealing a Victorian Tiled Floor

After leaving the floor to dry completely for a couple of days, I returned to the property to seal the tiles. Once satisfied that the floor was damp-free and ready to be sealed, I chose to apply a combination of two products.

Firstly, I applied a coat of Tile Doctor Colour Grow, which is an impregnating sealer designed to enhance the natural colours and shades in the stone, but with a matte finish. Secondly, I applied a few coats of Tile Doctor Seal & Go, which provides the high quality, durable sheen finish that the customer had requested.

Victorian Tiled Floor After Cleaning Oxford

Having the best of both worlds with these sealers really worked wonders for the appearance of the tiles and would highly recommend this combination of sealers for Victorian tiles. The customer was very pleased with the result of the restoration and can now enjoy her fully renovated house – complete with a fantastic looking Victorian tiled floor.

Professional Victorian Tiled Floor Restoration in Oxfordshire

Victorian Tiles Refreshed After Property Renovation in Oxford Read More »

Dull Slate Tiled Kitchen Floor Refreshed in Oxford

1 Comment / Oxford Tile Cleaning, Slate Tile Cleaning, Work History / Barry Woodward

These Slate kitchen floor tiles at a property in Oxford were in good physical condition, but had become dull over time due to heavy usage, and upon close inspection the grout was stained. The customer contacted me as she was keen to get the tiles back to looking their best. This would require a thorough clean and the application of a fresh sealer.

While Slate floor tiles are reputed to be hard wearing and damage resistant – and are therefore a popular choice for high traffic areas like kitchens – this does not exclude them from needing regular maintenance.

Cleaning a Dull Slate Tiled Kitchen Floor

To begin, I mixed a strong solution of Tile Doctor Pro Clean and water. Pro-Clean is a versatile cleaner that when used in a weak dilution can be used as a regular cleaner for most types of natural stone floor, including more sensitive stones such as Limestone and Marble.

The cleaning was then spread across the surface area of the floor, and left it to dwell for ten minutes to allow the solution to seep into the pores of the stone and lift the ingrained dirt to the surface. Pro-Clean in a strong dilution also functions as a stripping product, meaning it works to strip away any old and ineffectual sealer.

I then scrubbed the solution into the floor using a stiff scrubbing brush, paying particular attention to the grout in order to break down the visible staining. The tiles and grout lines came up really well during the cleaning process – this became clear once I had rinsed the floor and removed the residue using a wet vacuum.

Sealing a Slate Tiled Kitchen Floor

With the customer eager to have the job completed quickly, I installed portable room dryers and utilised a heat gun to dry the floor, allowing me to seal it on the same day.

Once I had ensured the floor was completely dry, I commenced the sealing process by firstly applying a coat of Tile Doctor Stone Oil, a product which is designed to bring out all of the natural dark shades in the Slate.

When this was dry, I applied a single coat of Tile Doctor Colour Grow. This is an impregnating sealer, meaning that it soaks into pores of the stone to provide durable protection from within against ingrained dirt and stains. Colour Grow also enhances the natural colours in the stone even further.

The customer was amazed by just how big a difference could be made to the tiles in the space of just a day. Although the tiles were generally in very good nick, my main task was to be liven them up – judging by the before and after photos, I think this was achieved. And, now that they have been treated to a fresh seal, the tiles will be prevented from quickly becoming dull again.

Restoring the Appearance of a Slate Tiled Floor in Oxfordshire

Dull Slate Tiled Kitchen Floor Refreshed in Oxford Read More »

Victorian Tiled Floor with Gas Pipe Trench Repaired and Restored in Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

This house in the historic university city of Oxford had a gas fire installed in the living room and unfortunately the only route to the gas supply in the under stairs cupboard was via to go under the Victorian tiled floor in the hallway. Unfortunately this was a bit of a butcher’s job and a trench was dug into the floor which the current owner however was very keen on restoring back to its original condition.

I visited the client just before the Christmas break last year, and agreed that I would firstly replace the missing tiles and then return after Christmas to give the floor a deep clean and seal.

Victorian Floor Gas Pipe trench in Oxford

Repairing a Victorian tiled floor

In order to properly repair this Victorian tiled floor, I firstly had to source tiles that would be consistent with the colour and pattern of the original design. Since Victorian tiles are known for their intricate and varied designs, this isn’t always an easy task. However, I was able to find the right tiles in good time, although naturally being new they were brighter than the existing which had seem some wear but they should blend in over time. I proceeded to fill the deep part of the hole with concrete, before carefully laying down the tiles in line with the specific pattern on the rest of the floor. I then grouted the new tiles in to finish the repair.

Victorian Floor- Gas Pipe Repaired in Oxford

Cleaning a Victorian tiled floor

After the Christmas break, I returned to the house to commence the cleaning and sealing processes. My first task was to mix a solution of the two cleaning products, Tile Doctor Nanotech HBU and Pro Clean and let this soak into the tiles.

Nanotech is a particularly powerful cleaner which uses nano-sized particles to penetrate deep beneath the surface of the stone to lift out ingrained dirt. Pro Clean is a high alkaline cleaner that also contains stripping properties to break down any old sealer and mixed together the two products make a very powerful tile cleaning product.

I applied the solution to the floor and left it to dwell for a full hour before agitating with a scrubbing brush to remove any dirt. Following this I used my wet vacuum to soak up the soiled solution, before thoroughly rinsing the floor with clean water extracting again using the wet vacuum.

Sealing a Victorian tiled floor

I left the floor for 24 hours in order to let it dry completely following the clean. Upon my return I sealed the tiles using Tile Doctor Seal & Go, which adds a stain resistant and robust surface seal, along with a nice low sheen finish.

Victorian Floor Gas Pipe Repaired and cleaned in Oxford

It took some work but I think your will agree the floor now looks fantastic and the sealer should keep it looking that way for some time to come.

Professional Tiled Floor Repair and Restoration in Oxfordshire

Victorian Tiled Floor with Gas Pipe Trench Repaired and Restored in Oxford Read More »

Quarry Tiled Kitchen Floor Deep Cleaned and Sealed in Milton

1 Comment / Quarry Tile Cleaning, Work History / Barry Woodward

Not too long ago I visited a client who had just moved into a lovely old cottage in Milton, Oxfordshire. She wanted to restore many of the antique features of the building, including a fantastic Quarry tiled floor in the kitchen.

Quarry is typically a robust, hard wearing stone, but in a high traffic area like a kitchen, the tiles will need regular maintenance. These tiles clearly hadn’t seen a thorough clean and fresh seal in a long time, and so I was called in to provide just that.

Quarry Tiled Kitchen floor Before Cleaning Milton

Deep cleaning an old Quarry tiled floor

On the first day of work, I gave the Quarry tiles a deep clean using a strong solution of Tile Doctor Pro-Clean and water. Pro-Clean is a versatile alkaline cleaner that also helps to break down any old and no longer effectual sealer remaining on the tiles.

The solution was applied evenly to the floor and left to dwell for half an hour, allowing time for it to seep into the stone to get underneath and lift out the ingrained dirt. I then removed the dirt by agitating the solution with a scrubbing pad fitted to a rotary floor scrubber. I worked in small sections at first, and gradually finished the entire floor.

After completing the initial clean, I rinsed away the soiled solution and vacuumed up the excess moisture using a wet-vac machine. I then scrubbed the floor an acid wash using a dilution of Tile Doctor Grout Clean-Up to remove grout smears and other mineral type deposits. The resulting solution was then removed in a similar fashion using a wet-vac.

The final step in the cleaning process was to rinse the floor with Tile Doctor pH Neutral Cleaner to remove any trace of product helps to tackle any remaining dirt and reset the pH balance of the tiles before sealing.

Sealing a Quarry tiled floor

After leaving the floor to dry overnight, I returned the next day to the house to seal the floor with Tile Doctor Seal & Go, a water-based topical sealer which gives the floor an aesthetically pleasing sheen and a robust surface seal.

Quarry Tiled Kitchen floor After Cleaning Milton

The photos demonstrate the results better than this short account can, needless to say the floor is now transformed.

Professional tile cleaning and sealing of an old Quarry tiled floor in Oxfordshire

Quarry Tiled Kitchen Floor Deep Cleaned and Sealed in Milton Read More »

Deep Clean and fresh Seal for Victorian tiled floor in Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

This fantastic Victorian tiled hallway floor in Oxford was in good physical condition for its age; however like any sealed floor the sealer had worn down with use and with dirt becoming trapped in the pores of the tile it was now becoming difficult to clean effectively and had become dull and un-inviting. It was now due a really good deep clean and re-seal. Oxford as I’m sure your aware has a rich history and is home to one of the world’s best universities, so not surprisingly many houses here have interesting floors such as this one.

Victorian Tiled Hallway Oxford Before Cleaning

Cleaning a dirty Victorian tiled floor

Upon my arrival at the house, my first task was to protect the skirting boards, as well as the wooden floors leading into the other rooms. I then mixed a solution of Tile Doctor Pro-Clean, a versatile, high alkaline cleaner combined 50:50 with Tile Doctor NanoTech HBU, a particularly strong cleaner that utilises nano-sized particles to penetrate into areas of the stone that standard products simply cannot reach.

I applied the solution to the surface and allowed it to soak for thirty minutes, allowing it to get to work on the ingrained dirt so it could be easily removed. Following this, I agitated the solution with a soft brush attached to a rotary scrubbing machine. I then applied more solution and left it for a further thirty minutes, before scrubbing this into the tiles using a black pad fitted to the rotary machine.

After the clean had been completed, I rinsed the entire floor multiple times and vacuumed up the resulting slurry using a wet-vac machine.

Sealing a Victorian tiled floor

I left the floor overnight, allowing the surface enough time to dry and returned then next day to seal the floor, checking first to ensure the tiles had dried. To seal the floor I used several coatings of Tile Doctor Seal & Go. Seal & Go which is a water-based, topical sealer that is suitable for use on unsealed, porous surfaces such as Victorian tile, textured Quarry, Slate, and Sandstone; being water based you don’t get the smell so it’s much more pleasant to work with.

Victorian Tiled Hallway Oxford After Cleaning

As you can see from the before and after photos, the result was an aesthetically pleasing and – most importantly – clean, Victorian tiled floor. Needless to say, my client was extremely pleased with my work.

Maintaining a Victorian Tiled Hallway Floor in Oxfordshire

Deep Clean and fresh Seal for Victorian tiled floor in Oxford Read More »

Cleaning and Sealing a Slate patio in Chinnor

1 Comment / Slate Tile Cleaning, Work History / Barry Woodward

Back here with another job, this time in the small commuter town of Chinnor in Oxfordshire to clean and seal a Slate patio which was looking worse for wear. Slate is a highly durable material that is a popular choice not only for external flooring such as patio, but also for internal flooring in high traffic areas like kitchens and hallways. A few days before I began the cleaning, I visited the property in order to rake and re-fill the grout.

Cleaning a Slate patio

Working in sections, I began the cleaning process by pre-wetting the individual area of the patio, before applying a dilution of Tile Doctor Pro Clean. I use Pro-Clean as a cleaner for several different types of stone flooring, whether internal or external, as it is very good at getting underneath the dirt and lifting it out, being an alkaline it’s also safe to use on all types of Tile and Stone.

The solution was left to on the surface to dwell for a while, before scrubbing in with a medium brush attached to a floor machine. Once I had finished cleaning, I used a wet-vac machine to remove any watery residue before rinsing the area with clean water, and soaking up the excess once again with the wet-vac. I repeated this same process for the entire patio.

Sealing a Slate patio

Before beginning the sealing process, I ensured that the floor was completely dry, as any excess moisture could have impacted negatively on the performance of the sealer. My sealer of choice was Tile Doctor Colour Grow, a colour enhancing, impregnating sealer; two coats were sufficient.

As an impregnating sealer, Colour Grow works its way into the pores of the Slate, providing durable surface protection from within. In addition, the colour intensifying properties of Colour Grow bring out the natural colours and shades in the surfaces to which it is applied.

The finished result, as you can see from the photos, was quite a different look for this Slate patio. The many layers of grime and dirt had previously hidden the fantastic character of the tiles, but with a good clean and colour enhancing seal, the patio was brought back to life. Both myself and my client were very pleased with the outcome.

Patio Restoration in Chinnor

Cleaning and Sealing a Slate patio in Chinnor Read More »

Victorian Floor Restoration Oxford After Sealing

Full restoration of a Victorian tiled floor in Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

I was recently called to a property in the historic city of Oxford, perhaps most famous for being the site of the oldest University in the English-speaking world. The property owner asked me to take a look at a linoleum floor, which was partially revealing a black and white patterned, Victorian tiled floor underneath, to see what I could do with it. Although it would be a challenging and lengthy job, I assured my client that I would be able to restore the hidden Victorian tiled floor to its original condition.

Victorian Floor Restoration Oxford Before

Removing the linoleum covering and cleaning the floor

My first task was to carefully scrape off as much of the linoleum covering as possible without damaging the floor beneath.

Victorian Floor Restoration Oxford Lino Removed

Once the linoleum had been removed, my next step was an initial clean of the floor.
Firstly, I applied a layer of Tile Doctor Remove and Go, which would help to draw out the ingrained dirt and stains. I left the product to dwell for only a short time as I did not want it to dry on the surface of the floor. Following this, I scrubbed the floor with a medium brush attached to a Rocky floor cleaning machine, before rinsing the area with clean water and then repeating the process again.

Victorian Floor Restoration Oxford Cleaning

To take the cleaning process a step further, I mixed a solution of Tile Doctor Pro-Clean and NanoTech HBU, which uses nano-sized particles to penetrate below particularly tough stains and lift them out. This solution was applied to the floor and left to dwell for roughly two hours. I then used my floor machine (which weighs 57kg when full) with a medium brush and scrubbed the surface once again. After completing the cleaning process, I made sure to rinse the floor multiple times in order to ensure all the products had been rinsed away.

Victorian Floor Restoration Oxford Repair

Floor repair, tile replacement and sealing

I then set about digging out the concrete lines that were in the floor; these were likely the reason for having the floor covered in linoleum in the first place. One area under the concrete lines contained a gas pipe, which I found to be obsolete, and another contained an electrical wire, which I had to test in order to ensure it too was no longer functioning. I dug out the concrete, and removed all the tiles around the edge of the room, where carpet grippers had been put down, effectively smashing nails into the floor.

Once I had sourced a total of 268 replacement tiles, I set about careful laying them down in a pattern that was consistent with the floor’s original appearance, once the tile adhesive was dry they were then grouted and the floor was then left for a week so they could set properly.

Victorian Floor Restoration Oxford Tile Repair

When I returned after this period, I mixed a solution of Tile Doctor Pro-Clean and water, and applied it to the floor. I left it to dwell for about 30 minutes, periodically stubbing with a deck brush. I then once again utilised my floor cleaning machine with a medium brush to scrub the floor, rinsed the area with more clean water, and then vacuumed up the excess liquid. The floor was let again to dry, this time for a period of a few days.

Victorian Floor Restoration Oxford Pre-Sealing

When I returned to the property after a few days, I used a damp meter to test the floor, making sure that the surface was dry enough to commence sealing (as any excess solution might have affected the performance of the sealer). My sealer of choice was Tile Doctor Seal & Go, a topical sealer which provides a sheen finish (as requested by my client) along with durable protection.

Overall, the job took more than three weeks to complete, but it was extremely satisfying to see the restored Victorian tiled floor, back to looking great again. My client was also very satisfied with my work, saying:

“We are delighted with the work Barry carried out for us. He had restored our floors with care and attention to detail, and we are really pleased with the final result!”

Restoring a Victorian Tiled Floor Hidden under Vinyl in Oxfordshire

Full restoration of a Victorian tiled floor in Oxford Read More »

Marble Bathroom Worktop in Abingdon After cleaning and polishing.

Refurbishing 12 Marble Bathroom Worktops at Abingdon Science Park

1 Comment / Abingdon Tile Cleaning, Marble Tile Cleaning, Work History / Barry Woodward

This job required the cleaning of Marble Worktops in twelve toilets at a very nice office in the Abingdon Science Park. The building was occupied by a company called Sophos who you may have heard of and over a period of time the Marble had become stained through the build-up of Limescale from the water supply and the cleaning company servicing the office could not clean it off. I’ve seen a few horror stories of stone surfaces being damaged through the use of acidic Limescale removers so the cleaning company was quite right not to touch it.

Polishing Marble Worktops

To remove the Limescale it would be necessary to hone the Marble using a set of small six inch burnishing pads fitted to a handheld buffing machine. The process involves starting with the coarse 400grit pad with a little water which cuts through the Limescale and then moving on to the 800, 1500 and finishing with 3000 grit to hone the surface and build the polish backup. The water helps lubricate the activity and the surface needs to be rinsed down between each pad.

Sealing Marble Worktops

When the surface was dry I applied two coats of Tile Doctor Colour Grow which is a colour enhancing sealer which impregnates the pores of the stone to protect it, it also enhances the natural colours in the stone.

There were twelve of these to do so as you can imagine it took me a while to get round.

If you are experiencing a similar problem with highly polished Marble do get in touch as we can achieve a mirror finish.

Limescale stained Marble bathroom worktops honed in Oxfordshire office

Refurbishing 12 Marble Bathroom Worktops at Abingdon Science Park Read More »

stained slate fireplace hearth Boars Hill After

Tackling a urine stained Slate fireplace hearth in Boars Hill

1 Comment / Fireplace Cleaning, Slate Tile Cleaning, Work History / Barry Woodward

I thought you might find this post interesting as it’s a little unusual. I had arrived at a client’s house in Boars Hill near Oxford to do a travertine floor and she asked if I could also take a look at her fireplace where one of her dogs had urinated on it. Urine is acidic so if not quickly removed it will start to eat away a sealer and in this case as you can see from the photo below it left a mark. It was quite a small area and as I already had the necessary products to deal with it I said no problem.

stained slate fireplace hearth Boars Hill Before

Cleaning a Slate Fireplace Hearth

The urine had penetrated the existing protective seal so to get a uniform appearance it was going to be necessary to remove the covering and re-seal. To do this I covered the hearth in Tile Doctor Remove and Go which is a tile and stone friendly product for removing of protective coatings. This was carefully scrubbed into the stone and bit by bit the old wax/seal was removed exposing the bare slate.

Sealing a Slate Fireplace Hearth

The stripped slate was now clean and all trace of previous sealer had been removed but once it had fully dried was left looking washed out. This was easily remedied however by applying a coat of Tile Doctor Stone Oil which brought back the deep black colour. When the Stone Oil had dried I finished the job off by applying a coat of Tile Doctor Ultra Seal which is a natural look sealer that will protect the slate going forward.

Slate Fireplace Hearth Stripped and Sealed in Oxfordshire

Tackling a urine stained Slate fireplace hearth in Boars Hill Read More »

Mel Kendrick Markers Modern Art Wormsley After Cleaning

Cleaning Contemporary Concrete Artwork at the Wormsley Estate

2 Comments / Work History / Barry Woodward

This was an unusual request to clean a modern piece of contemporary artwork by New York City artist Mel Kendrick on display in one of the gardens of the Wormsley Estate. I’m no art expert but having done some research on the internet it appears to be part of a collection known as “Markers” that were on display at the Madison Square Park in 2009. The work is made from concrete cast into different coloured sections and fitted together to form a rather larger piece of art which having been exposed to the UK elements was now starting to discolour and go orange in part.

Mel Kendrick Markers Modern Art Wormsley Before Cleaning

Cleaning Modern Concrete Artwork

Being such a prestigious work of art i had to be careful not to damage the stone in anyway so after careful consideration I worked out a process using an alkaline cleaning product Tile Doctor Pro-Clean.

To get the statue clean I used a warm water dilution of Tile Doctor Pro Clean working it into small areas at a time spraying the solution on and scrubbing with a brush, then rinsing it off with clean water. This process took some time but certainly did the trick.

Sealing a Concrete Artwork

With this project being outdoors and with it taking a couple of days I had to pick a good weather window and fortunately the weather held out long enough so I could continue and seal the concrete in order to protect it going forward. Again careful consideration had to be given to the choice of sealer and in the end I went with Tile Doctor Ultra Seal which is an impregnating sealer that soaks into the pores protecting from within and most importantly it’s a natural look sealer that does not change or enhance the colours.

If you’re a lover a modern art then you should appreciate the difference and will agree with me that the statue now looks new again.

Modern Statue Artwork Cleaned and Sealed in Oxfordshire

Cleaning Contemporary Concrete Artwork at the Wormsley Estate Read More »

Terracotta Tiled Floor After Cleaning Oxford

Cleaning and Sealing a Terracotta Tiled Floor in Oxford

1 Comment / Oxford Tile Cleaning, Terracotta Tile Cleaning, Work History / Barry Woodward

The before picture below was actually taken after another cleaning company had come in to clean these Terracotta floor tiles for a client in the city of Oxford; well what can I say except they then called Tile Doctor.

Terracotta Tiled Floor Before Cleaning Oxford

Cleaning Terracotta Tile

I started by doing a test on a small area and realised that I could strip the remaining sealer from the floor with a strong dilution of Tile Doctor Pro Clean which is also an effective cleaner and safe to use on stone and tiled floors. So I diluted Pro Clean with warm water and spread this on the floor leaving it to dwell for twenty minutes before scrubbing it in with a black padf fitted to my Rocky floor machine. This worked very well on the floor and the cleaning solution was soon dirty with the released soil which was removed using a wet vacuum and more water to rinse it away and dry the floor as much as possible.

Sealing Terracotta Tile

Satisfied that the floor was now as clean as it could be I left for the day and returned the next day to seal the floor, first checking that the tiles were dry and ready to be sealed.

Sealing was done in two stages starting with an initial coat of Tile Doctor Colour Grow which is an impregnating sealer that adds life to the natural colours in the tiles and gives the floor a good base for the next sealer. The second stage was to apply a few coats of Tile Doctor Seal & Go which builds up a surface seal that leaves a nice sheen to the floor as requested by the customer.

Terracotta Floor Cleaned and Sealed in Oxfordshire

Cleaning and Sealing a Terracotta Tiled Floor in Oxford Read More »

Coloured Slate Tiled Floor Barnard Gate After Cleaning

Cleaning Multi-Coloured Slate Tiled in a Barnard Gate Kitchen

1 Comment / Slate Tile Cleaning, Work History / Barry Woodward

This Multi-Coloured Slate tiled floor in the kitchen of a property in Barnard Gate near Witney was in good solid condition with no damage but had been poorly maintained with layers of sealer applied to un-clean tiled; the new home owners were keen to make this floor into a talking point as you entered the property and asked us to address the problem.

Coloured Slate Tiled Floor Barnard Gate Before Cleaning

Deep Cleaning a Slate Tiled Floor

The first task was to remove the layers of sealer from the tile so on day one the floor was covered with Tile Doctor Remove and Go which was left this to dwell for a while so it could soak into the pores of the slate and penetrate the remaining sealer. The product was then scrubbed into the tile with a Rocky rotary floor scrubber and then rinsed off with clean water and dried with a wet vacuum. The next process was to clean the floor with a strong mix of Tile Doctor Pro Clean to remove the remaining dirt in the floor and to scrub the grout clean, again the rotary floor machine came in useful for this task and again the floor was thoroughly rinsed with clean water a few times and dried with the wet vacuum. I then left the floor for a couple of days to allow enough for it to completely dry before sealing.

Sealing Slate Kitchen Tiles

To seal the slate I first applied a coat of Tile Doctor Colour Grow which is an impregnating sealer the gets into the pores of the stone and also enhances the natural colours. I then applied a few coats of Tile Doctor Seal and Go which is a topical sealer that added a nice sheen finish that the customer wanted.

The end result was fantastic and the combination of the two sealers really got the best from the slate which is now very much appreciated and loved by the customer.

Colourful Slate tiles Cleaned and Sealed in Oxfordshire

Cleaning Multi-Coloured Slate Tiled in a Barnard Gate Kitchen Read More »

Victorian Tiled Floor Oxford After Cleaning

Refreshing a Victorian Tiled floor in Oxford

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

The Victorian tiled floor shown below comprised of a complex square and diamond pattern contained with a parallel border and must of take a lot of work when it was first installed. It had been a while since it was last given a deep clean and was now looking rather dull and lifeless; we come across a lot of these floors at Tile Doctor and the remedy is a straight forward deep clean and reseal.

Victorian Tiled Floor Oxford Before Cleaning

Restoring Victorian Quarry Tiles

The first task was to clean the floor with a dilution of Tile Doctor Pro-Clean which was left to dwell on the tiles for a short while before being scrubbed in washing the floor down afterwards and extracting it with a wet vacuum to remove the soiled cleaning solution.

This did a reasonable job of cleaning up the tiles but there were some stubborn areas that would need further attention and what I suspected to be remnants of an old sealer. A stronger product was required and so the next step was to cover half the floor with Tile Doctor Remove & Go leave it to dwell for a time and then scrub the floor again with a rotary machine fitted with a scrubbing pad. Again the tiles were rinsed and the dirty cleaning solution removed using a wet vacuum. Once done the process was repeated on the other half of the floor. Working in sections like this allows more room in what was a tight hallway and also ensures the cleaning products don’t dry out.

This process removed all the old seal and drew out the ingrained dirt. I them rinsed the floor with a dilution of Tile Doctor Grout Clean Up to deal with a few stains and grout problems before removing it with the wet vacuum and giving the entire floor a thorough rinse with water which was repeated a couple of times; again the wet vacuum was used to extract the water from the tiles and get them as dry as possible.

Sealing Victorian Tiles

I had finished cleaning the floor and so left for the evening returning four days later to seal the floor. Fortunately the customer had planned a short break away so the tiles were nice and dry and still clean on my return.

To seal I applied a single coat of Tile Doctor Colour Grow which is an impregnating sealer to give a good base followed by three coats of Tile Doctor Seal & Go which is a topical sealer that added the shine the customer required.

Victorian Tiled Hallway cleaning in Oxfordshire

Refreshing a Victorian Tiled floor in Oxford Read More »

Victorian Tiles After Refurbishment in Farringdon

Victorian Tiled Floor Refurbished in Farringdon

1 Comment / Grout Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

Apologies for the first photograph, I realise now it’s a little out of focus but hopefully you can see that the Victorian Tiled Floor pictured (at a residence in the market town of Farringdon, Oxfordshire) was not looking its best and this was mainly due to the fact that the house had recently undergone some extensive building work and had become very dirty in the process.

Victorian Tiles Before Refurbishment in Farringdon

Refurbishing Victorian Tiles

The first thing I did was protect the skirting board and doors from splashes and then to clean the floor I applied a strong dilution of Tile Doctor Pro Clean and this was left to dwell on the floor for a good twenty minutes. It was then worked into the tile using a deck brush and then more Pro-Clean was applied so the floor didn’t dry. I then scrubbed the floor with a rotary floor machine fitted with a scrubbing pad. After I finished the soiled cleaning solution was extracted using a wet vacuum and the whole floor was then rinsed with clean water to remove any trace of cleaning product. The tiles were then inspected and the process re-applied to areas that needed it; I then left the floor for two days so it could dry thoroughly.

Sealing Victorian Quarry Tiles

When I returned the floor was dry so I sealed it using a single coat of Tile Doctor Colour Grow followed by four coats of Tile Doctor Seal & Go. This is a great combination as the Colour Grow impregnates the tile improving the colours and protecting it from within whilst Seal and Go adds a further layer of protection and also added a nice subtle shine that the customer wanted.

Victorian Tiled floor Deep Cleaned and Sealed in Farringdon

Victorian Tiled Floor Refurbished in Farringdon Read More »

Quarry Tiles After Cleaning in Watlington

Quarry Tiled Floor Restored in Office at Watlington

1 Comment / Quarry Tile Cleaning, Work History / Barry Woodward

A company based in the 17th century market town of Watlington were renovating their office space and decided to replace the carpet which had been glued to the floor below. Upon further inspection this turned out to be a Quarry Tiled Floor and they were keen to restore it and so we got the call.

Quarry Tiles Before Cleaning in Watlington

Restoring Quarry Tiles

I first covered the whole floor with Tile Doctor Remove and Go, leaving this to dwell for a while whilst I fitted a scrubbing pad to my rotary machine. Once the machine was ready the whole floor was scrubbed followed by a rinse with water; the resultant soil was then extracted from the floor using a wet vacuum. This process removed most of the glue so I repeated the process until satisfied all the glue had gone. Remove and Go lives up to its name and although normally used to remove sealers it will remove most other coatings as well. This process took up most of the day so after the final and thorough rinse I left the floor to dry aiming to come back the next day to seal it.

When I returned the next day the floor had white patches of effervescence on it where salts had been forced up through the tile as the water evaporated; this had to be dealt with before the tiles could be sealed so I spent the second day scrubbing the entire floor with Grout Clean Up to remove it, after finishing the floor was given another thorough rinse to remove any product from the floor and used the wet vacuum again to get it as dry as possible.

Sealing a Quarry Tiled floor

I returned the third day to a nice dry and most importantly clean floor. To seal Quarry tiles I usually go for Tile Doctor Seal and Go as it’s water based (so no smell) and it adds a nice shine to the floor; however in this case being an office environment with a lot of heavy traffic I decided to go with Tile Doctor Colour Grow which is an impregnating sealer that soaks into the pores of the tile and is likely to be more durable, it also enhances the natural colours in the tile leading to a very nice finish.

I think you will agree the final result was a remarkable transformation

Commercial Quarry Tiled floor Restored in Oxfordshire

Quarry Tiled Floor Restored in Office at Watlington Read More »

Brick Paved Floor After Regrouting and Cleaning Peppard

Brick Paved Floor Re-grouted and Cleaned in Peppard

1 Comment / Work History / Barry Woodward

The owner of this house in Peppard Common near Henley on Thames was keen to have the grout completely removed from this brick paved floor in the Kitchen and re-done. This is a lot of work and re-colouring the grout with a Grout Colourant kit would have been faster and easier however it is something we can do if required.

Brick Paved Floor Before Regrouting and Cleaning Peppard

Removing Grout

I started by removing the kick boards around the base of the kitchen units then to remove the grout I had to cut along all the grout lines with a hand held multi tool; as you can imagine this work is quite painstaking and slow however I persisted and eventually completed the task which took me the whole day. After this I came back the next day and grouted the whole floor polishing off the excess grout as I went.

Cleaning Brick Paving

On the third day I gave the floor a clean with Tile Doctor Pro Clean diluted with water. The customer did not want a full scrub as the brick floor had a nice patina to it and a full scrub would have made the brick floor more of an orange colour. The last step was to give the floor a thorough rinse with water and then use a wet vacuum to extract as much water from the floor as possible.

In total the job took three days to complete and it now looks much cleaner and fresher.

Grouting and Cleaning a Brick Paved Kitchen Floor in Oxfordshire

Brick Paved Floor Re-grouted and Cleaned in Peppard Read More »

Restoring a Victorian Tiled Floor in Oxford hidden under Parquet

1 Comment / Oxford Tile Cleaning, Victorian Tile Cleaning, Work History / Barry Woodward

Let me start this story by telling you this was the most challenging floor that I have come across so far. It all started with a request to visit a property in Oxford where they had discovered an original Victorian tiled floor under a parquet floor in the hall.

When I arrived the customer had taken up a small area in the corner and had already tried to remove the black bitumen that the parquet floor was stuck down with, he had made some progress but realized it would be a massive project without the right tools. After I had showed him how much cleaner I could take his patch he booked me to restore the floor, the customer said he would remove the parquet floor himself.

Removing Bitumen from Victorian Tiles

When I arrived the parquet had been taken up to reveal a completely bitumen covered tiled floor that was very sticky. My first task was to put protection around the doors and skirting before moving on to removing the bitumen which was done by covering the half the floor in a mixture of Tile Doctor Remove and Go combined with Nano Tech UltraClean which was left to soak in for about an hour.

After this I scrubbed the solution into the floor using a black scrubbing pad on my Rocky floor scrubbing machine, this loosened the bitumen from the floor which was then washed off with water and removed using a numatic wet vacuum. The same process was repeated on the other half of the floor and then the whole process was repeated again on both parts of the floor until it was clear of bitumen. This was arduous work and took a whole day to complete.

Cleaning Victorian Tiles

When I returned the next day I gave the floor a deep clean using a medium dilution of Tile Doctor Pro Clean, like the Remove and Go this was spread over the floor leaving it to dwell for 10 minutes before being scrubbed in using the scrubbing machine fitted with a black pad; again the floor was rinsed clean with water which was removed using the wet vacuum.

After this I applied Tile Doctor Grout Clean Up which is an acidic product that is great at removing grout smears and mineral deposits from tiles, being an acid you can only leave it on the tile for a short while so I worked in 1m square sections at a time on my knees spraying and scrubbing with a deck brush and then rinsing.

When I had finished this process the whole floor was thoroughly rinsed with clean water to ensure there were no cleaning products left on the floor. I then left the floor to dry promising to return a few days later when it had dried.

Sealing Victorian Quarry Tiles

I returned as agreed a few days later to seal the floor with five coats of Tile Doctor Seal and Go which is a great for Victorian tiles as it leaves a nice shine to the floor which is exactly how the customer wanted it. This process does take time however as you have to let the first coat dry before moving onto the next.

From start to finish the transformation of the floor was amazing and the customer was very impressed with the results. Although the area was not large this was a very testing floor as bitumen stays sticky and was very difficult to remove even with the correct machines and products.

Victorian Tiled Hall Restored in Oxford

Restoring a Victorian Tiled Floor in Oxford hidden under Parquet Read More »

Terracotta Tiled Floor in Great Bourton After Cleaning

Terracotta Tiled Floor Cleaned and Sealed in Great Bourton

1 Comment / Terracotta Tile Cleaning, Work History / Barry Woodward

At first glance and this Terracotta tiled floor at a house in the village of Great Bourton looks in good condition, but on closer inspection there were visible white marks where there had been a water leak in previous years and the salts had come through the tiles. The customer also told me she had to wax the floor on a regular basis and was looking for a seal where she didn’t have to do this.

Terracotta Tiled Floor in Great Bourton Before Cleaning 1

Terracotta Tiled Floor in Great Bourton Before Cleaning 2

Cleaning Terracotta Tile

My first task was to protect all the skirting and kickboards with protective tape. I then mixed Tile Doctor Pro Clean with water and spread it over a section of the floor and then left it to dwell for a few minutes. The solution was then scrubbed in with a black pad on a 17inch rotary floor scrubbing machine. I then used a wet vacuum to remove the slurry and rinsed the floor with water. This process was repeated this process until the whole floor was scrubbed and rinsed with any stubborn areas re-treated.

To remove the white salts from the Terracotta I applied Tile Doctor Grout Clean Up over the floor which was scrubbed in and then removed using the wet vacuum. The whole floor was then thoroughly rinsed with water and the wet vacuum used to suck up the water until it the surface was dry.

The photograph below shows the terracotta floor at this stage with the floor clean and stripped back before re-sealing. I left the floor a couple of days at this point to allow it fully dry before applying the sealer.

Terracotta Tiled Floor in Great Bourton After Stripping

Sealing Terracotta Tile

On my return I checked the floor had dried and then applied two coats of Tile Doctor Colour Grow which is an impregnating seal that enhances the natural colour of terracotta, I then added five coats of Tile Doctor Seal and Go which is a topical sealer giving it the nice finish the customer required.

The customer was really pleased with the results and also relieved that she would not have to keep waxing the floor; whilst I was there I demonstrated how to clean the floor using Tile Doctor Neutral cleaner which unlike acidic cleaners will not harm the sealer.

Terracotta Tiled Floor in Great Bourton After Cleaning 1

Terracotta Tiled Floor in Great Bourton After Cleaning 2

The floor looks much better and certainly my customer thought so and left the following feedback on the system.

Very pleasant young man and he has done a great job. The kitchen floor is transformed. Thank you Barry!

Terracotta Floor Cleaned and Sealed in Oxfordshire

Terracotta Tiled Floor Cleaned and Sealed in Great Bourton Read More »

Limestone Entrance Hall Burford After Burnishing

Limestone Tiled Entrance Hall Cleaned in Burford

1 Comment / Limestone Tile Cleaning and Polishing, Work History / Barry Woodward

This Limestone tiled floor was located in the entrance hall of a residential property in Burford. I popped round following a cleaning enquiry to provide a quote and did a sample clean on a test area, I was then asked if I could do the whole floor there and then and not wanting to disappoint I managed to shuffle a few appointments round and got on with it.

Limestone-Entrance-Hall-Burford-Before-Cleaning

Cleaning Limestone Floor Tiles

To get the best from this floor I used a set of diamond encrusted burnishing pads which if you have read any of my previous posts you will remember we always recommend these for hard stone floors such as Limestone, Travertine and Marble. They come in four different grades from coarse to very fine and you work your way through them starting off with the coarse stripper pad with a little just water and then carry on with the remaining pads which are a finer and finer grade until the floor is thoroughly cleaned, polished and any previous sealer removed. Next step was to use Tile Doctor Pro-Clean along the grout lines with a stiff brush to get the grout clean. When done the floor was washed down with water which was then removed from the tile using a wet vacuum and then left to dry.

Sealing Limestone Floor Tiles

Once the floor was dry it was sealed using two coats of Tile Doctor Colour Grow which is a colour enhancing sealer which provides maximum stain protection on natural stone floors whilst bringing out the deep colour in the stone. The last step was to buff the floor to a nice shine with a rotary machine fitted with a white buffing pad.

The customer was very pleased with the results so much so she booked me to clean the grout on her kitchen floor.

Limestone Floor Cleaned, Polished and Sealed in Burford

Limestone Tiled Entrance Hall Cleaned in Burford Read More »

Travertine Tiled Floor Maintained in Brightwell-Cum-Sotwell

1 Comment / Travertine Tile Cleaning, Work History / Barry Woodward

This Travertine tiled floor had been laid in a house in the picturesque village of Brightwell-Cum-Sotwell in south Oxfordshire and the owner had decided it was time to have it properly cleaned and re-sealed.

Cleaning Travertine Floor Tiles

The floor was given a wash with Tile Doctor Neutral Cleaner to remove any surface grit and we then filled the small holes, which are quite a common feature of natural travertine, with a matching coloured grout.

This was then followed by the use of the Tile Doctor burnishing system which involves the use of a set of four Burnishing pads fitted to a rotary machine. There are four pads and you start off with a course stripper pad with a little just water and then carry on with the white pad and then the yellow pad until the floor is thoroughly cleaned and any previous sealer removed. Next step was to use Tile Doctor Pro-Clean along the grout lines with a stiff brush to get the grout cleaner.

To bring up the polish on the Travertine tile you then apply the last of the four burnishing pads with gives a final polish.

Sealing Limestone Floor Tiles

To seal the floor and protect it from staining two coats of Tile Doctor Colour Grow as applied; Colour Grow is a colour enhancing sealer which enhanced the natural colours in the stone. Once dry the last step was to buff the floor to a nice shine with a rotary machine fitted with a white pad..

Travertine Floor Cleaned, Polished and Sealed in Oxfordshire

Travertine Tiled Floor Maintained in Brightwell-Cum-Sotwell Read More »

Author name: Barry Woodward

Removing Limescale from a Granite Worktop and Sink

Granite Kitchen Worktop Aftercare

Professional Renovation of a Limescale Stained Granite Worktop in Oxfordshire

Deep Cleaning a Travertine Patio

Professional Renovation of a Large Travertine Patio in Oxfordshire

Polishing a Limestone Tiled Table

Sealing a Limestone Table

Professional Restoration of a Limestone Table in Oxfordshire

Cleaning a Quarry Tiled Paint Shop Floor

Sealing a Quarry Tiled Paint Shop Floor

Professional Restoration of a Quarry Tiled Paint Shop in Oxfordshire

Restoring and Replacing Old Quarry Tiles

Sealing Old Quarry Tiles

Professional Restoration of a Quarry Tiled Pub Floor in Oxfordshire

Renovating an Indian Sandstone Patio in Headington

Professional Restoration of an Indian Sandstone Paved Patio in Oxfordshire

Cleaning and Repairing a Victorian Tiled Hallway Floor

Sealing a Victorian Tiled Hallway Floor

Professional Restoration of a Victorian Tiled Hallway in Oxfordshire

Cleaning a Travertine Tiled Hair Salon Floor

Sealing a Travertine Tiled Hair Salon Floor

Professional Restoration of a Travertine Tiled Hallway in Oxfordshire

Deep Cleaning a Ceramic Tiled Shower Cubicle

Sealing a Ceramic Shower Tiles

Professional Shower Cubicle Cleaning in Oxfordshire

Cleaning Terracotta Tile

Sealing Terracotta Tile

Terracotta Floor Deep Cleaned and Sealed in Oxfordshire

Cleaning Terracotta Tile

Sealing Terracotta Tile

Terracotta Floor Cleaned and Sealed in the Cotswolds

Polishing an Etched Marble Vanity Countertop

Sealing a Marble Vanity Top

Professional Restoration of a Marble Vanity Countertop in Oxfordshire

Cleaning a Ceramic Tiled Shower Area

Professional Cleaning of Commercial Shower Tiling in Oxfordshire

Deep Cleaning a Slate Patio in Wantage

Sealing a Slate Patio in Wantage

Professional Restoration of a Slate Tiled Patio in Oxfordshire

Cleaning/Repairing a Tumbled Marble Tiled Kitchen/ Dining room Floor

Sealing a Tumbled Marble Tiled Kitchen/ Dining room Floor

Professional Renovation of a Tumbled Marble Tiled Floor in Oxfordshire

Cleaning a Coloured Slate Tiled Kitchen Floor

Sealing a Coloured Slate Tiled Kitchen Floor

Professional Clean of a Coloured Slate Tiled Kitchen Floor in Oxfordshire

Cleaning a Marble Tiled Shower

Polishing a Marble Tiled Shower

Professional Restoration of a Marble Tiled Shower in Oxfordshire

Removing Screed and Cleaning Kitchen Quarry Tiles

Sealing a Quarry Tiled Kitchen Floor

Professional Restoration of a Quarry Tiled Kitchen in Oxfordshire

Cleaning a Victorian Quarry Tiled Hallway Floor

Sealing a Victorian Tiled Hallway Floor

Professional Restoration of a Victorian Quarry Tiled Hallway in Oxfordshire

Cleaning a Victorian Tiled Hallway Floor

Sealing a Victorian Tiled Hallway Floor

Professional Restoration of a Victorian Tiled Hallway in Oxfordshire

Deep Cleaning Travertine Shower Tiles

Sealing a Travertine Tiled Shower Room

Professional Renovation of a Travertine Tiled Shower in Oxfordshire

Cleaning/Repairing a Victorian Tiled Hallway Floor

Sealing a Victorian Tiled Hallway Floor

Professional Restoration of a Victorian Tiled Hallway in Oxfordshire

Cleaning and Grouting Ceramic Tiled Bathroom in Oxford

Resealing Ceramic Tiled Bathroom in Oxford

Re Grouting and Sealing Ceramic Tiles in Bathroom Oxfordshire

Cleaning Limestone Floor Tiles

Sealing Limestone Floor Tiles

Limestone Floor Cleaned, Polished and Sealed in Radcot

Cleaning and Burnishing a Limestone Fireplace

Sealing a Limestone Fireplace

Professional Restoration of a Limestone Fireplace in Oxfordshire

Restoring Victorian Quarry Tiles

Sealing Victorian Tiles

Victorian Tiled Hallway cleaning in Oxfordshire

Restoring a Brick Floor

Sealing a Brick Floor

Professional Restoration of a Dirty Brick Living Room Floor in Oxfordshire

Cleaning Soiled Vinyl Floor Tiles